Getting Started; Time Setting; Alarm Function; Display Light - TFA EASY-CHARGE WIRELESS Instrucciones De Uso

Getting started

Remove the protective film from the display.
Connect the attached power adapter to the alarm clock. Insert the power adapter pin into the device jack
(Fig.1-H) and connect the plug to a wall socket.
Important! Make sure that your household voltage is no more than 240V!
Otherwise your device may be damaged.
The button cell battery will operate as a backup power source in the event of a power failure.
The device is ready for use.

Time setting

Press and hold the SNOOZE/DIMMER button (Fig.3-D) in normal mode to choose between the 12 - or 24-
hour system. In the 12-HR system AM (before noon) or PM (after noon) appears on the display (Fig.1-A).
Slide the switch (Fig.2-A) to the position TIME SET.
Press the  or  button (Fig.3-C,E) to set the time.
Press and hold the  or  button for fast mode.
After setting slide the switch to the position LOCK.
Press the DST ON/OFF button (Fig.1-G) to change the summer time in winter time and vice versa (+/- 1 hr).
In Daylight Saving Time DST (Fig.1-D) is shown on the display.
Note: If the alarm clock is first set up during summer time, please set the clock to winter time and press the
DST ON/OFF button when setting is complete.

Alarm function

Alarm time setting
Slide the switch (Fig.2-A) to the position ALM SET.
Press the  or  button (Fig.3-C,E) to set the desired alarm time.
Press and hold the  or  button for fast mode.
After setting slide the switch to the position LOCK.
Activate alarm
Slide the ALARM switch (Fig.2-B) to the position
The alarm is activated. The alarm symbol
Alarm clock function
When the set alarm time (Fig.1-K) is reached, the alarm clock will wake you up with the selected volume.
The alarm symbol (Fig.1-M) flashes.
If the alarm is not stopped manually, the ascending alarm tone automatically turns off after three minutes and
the alarm will be reactivated at the same set time on the following day.
The alarm symbol remains on the display.
Press any button to turn off the alarm sound or press the SNOOZE/DIMMER button (Fig.3-D)to activate the
snooze function.
The snooze symbol (Fig.1-C) will be flashing and the alarm will be interrupted for 5 minutes.
You can activate the snooze function up to 7 times.
Press any button to stop the snooze function.
Deactivate alarm
Slide the ALARM switch (Fig.2-B) to the position
The alarm function is deactivated. The alarm symbol
8
(loud) or (quiet).
(Fig.1-M) appears on the display.
.
(Fig.1-M) disappears.

Display light

Press the SNOOZE/DIMMER button (Fig.3-D) to adjust the brightness in 2 levels or to switch it off.
Briefly press the  or  button (Fig.3-C,E) several times to choose the desired colour.
Press and hold the  or  button to choose a continuous colour change.
Press the  or  button to stop the continuous colour change.
Charging function
Inductive charging of your mobile phone (according to Qi standard)
Put your mobile phone on the platform. Your phone should sit centred on the charging pad.
The charging symbol appears and the
fully charging.
The charging symbol does not appear or ERROR (Fig.1-E) flashes on the display if your device is not posi-
tioned properly or if your device is not compatible with the Qi standard. You may need to remove your phone
cover.
Compatibility may vary based on phone model. Please check your phone's manual for details.
Charging via USB
This product also provides a USB charging port for devices that do not support wireless charging.
Plug the USB cable (not included) into the USB port (Fig.1-J) port on the alarm clock and connect the other
end to your mobile device. Make sure that the charging rate is suitable for your mobile device.

Troubleshooting

Problem:
No display
No charging function (wireless)
Display ERROR
No charging function (USB)
If your device fails to work despite these measures, contact the retailer where you purchased the product.
(Fig.1-F) and the symbol flashes when your phone is success-
Solution:
Connect the device to the power adapter
Check the power adapter
Press the SNOOZE/DIMMER button to activate
the backlight
Mobile device is not Qi compatible
Position the mobile device properly
Remove metallic objects
Remove the cover
Use USB port
Check the USB port connection
9