Denon AVR-2802 Instrucciones De Operación página 18

ENGLISH
Learning function
• If your AV component is not a DENON product or it cannot be operated with the preset memory codesets,
you can "teach" the AVR-2802's remote control to "learn" the codes from the component's original remote
control.
• The buttons that can be "learned" are the CD, TAPE and CDR/MD system
buttons (see page 15) and the DVD, VDP, VCR and TV system buttons (see
page 17). (For the CD, CDR/MD, DVD, VDP and TV, the A block buttons can
also be "learned", and for the DVD and TV, the B block buttons can also be
"learned".)
1
Press the USE/LEARN selector button with the
tip of a pen etc., to set the learn mode. Both
the START and LEARNED/TX indicators flash.
Flashes
This unit's remote
control unit
2
Set the program switch to the side to be
learned.
Set to the AUDIO side for the CD, tape deck or
CDR/MD position, to the VIDEO side for the
DVD, VDP, VCR or TV position.
AUDIO
AVR/AVC VIDEO
3 Set the program switch to the position to be
learned.
TAPE CDR/MD
CD MULTI
DVD TV
VDP VCR
4 Set the remote control units so they are facing
each other, then press the button to be learned
on this unit's remote control unit.
Transmitting windows
Light
This unit's remote
control unit
The indicator stops flashing and the START LED
lights.
The learnable buttons are the buttons which can
be operated with the DENON system codes for
the CD player, tape deck, CD recorder, MD
recorder, the buttons which can be operated
with the preset memory for the DVD, VCR, VDP
and TV. For the TV only, however, the buttons in
the section indicated "A" on the diagram above
can also be "learned". Use these to "learn" TV
channels.
18
A
VCR-2/V.AUX
SPEAKER
DSP SIMULATION 5CH / 6CH STEREO
INPUT MODE
2 AUDIO
AVR/AVC
MEMORY
1,8
USE/LEARN T.TONE
5
Check that the START LED is lit, then press the
button to be "learned" on the other remote
control unit.
6
Once the START LED turns off and the
LEARNED/TX LED lights, release the button on
the other remote
control unit.
Other remote
control unit The two LEDs start
flashing again.
Approx.
7
To "learn" other buttons, repeat steps 2 to 6.
5 cm
8
Once the learning operation is completed,
press the USE/LEARN selector button again.
The two LEDs stop flashing and the learning
mode is cancelled.
NOTES:
• Up to 26 codes can be "learned", but this number may be lower if the codes are long.
• If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once
again light when the button(s) is released.
• If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For
limited number of models, codes cannot be stored in RC-904.
RC-904
START LEARNED/TX
SYSTEM CALL POWER
SET CALL OFF ON / SOURCE • If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full,
DVD VDP TUNER SHIFT
1 2 3
and the code you have just attempted to store was not stored.
TV/DBS PHONO
4 5 6
To "learn" that code, first perform the resetting operation. (See page 19.)
VCR-1 CD CDR / TAPE CHANNEL
7 8 9
TV/VCR
+10 0
A / B
4
VOLUME DISC SKIP+
DOLBY / DTS
SURROUND DIRECT System call function
STEREO
MASTER VOL.
ANALOG EXT.IN
• The included remote control unit is equipped with a system call function for transmitting multiple remote
TAPE CDR/MD
CD MULTI MUTING
3
VIDEO DVD TV control signals when a single button is pressed (this is often referred to as a "macro" function).
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER
This function can be used to turn on the amplifier's power, select the input source, turn on the monitor TV's
TITLE MENU/GUIDE
BAND RDS
CH SELECT B
power, turn on a source component's power and start playback, etc., all at the touch of a button.
ENTER
MODE PTY
SELECT
RT STATUS ON SCREEN
DISPLAY RETURN
(1) System call buttons
MULTI DVD
SET UP
The buttons that can be used for the system call function are shown on the table below.
A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up
to 5 operations can be performed with other buttons.
System call signals are already preset at the buttons indicated in the shaded section. System call signals can
also be stored at any button on the remote control unit, including the buttons in this section. (See page 19.)
No.
Button
transmissions
Other remote
control unit POWER OFF 10
POWER ON 10
DVD 5
This unit's remote VDP 5
control unit
TV/DBS 5
VCR-1 5
CD 5
(2) Using the system call function
1
Light
CALL
2
Press the button at which the desired system call signals are
stored while the LEARNED/TX LED is flashing.
• The preset signals or the signals you have stored at that
button are transmitted in succession.
Check that the stored
codes work properly.
Stored Stored Stored Stored Stored Stored
operation 1 operation 2 operation 3 operation 4 operation 5 operation 6
Receiver
DVD player DVD player
Receiver input source
(DVD) TV power on (DVD)
switched to
power on
power on playback
DVD
Receiver
LD player LD player
Receiver
input source
(VDP) TV power on (VDP)
power on switched to
power on playback
The system call signals for the POWER
VDP
OFF and POWER ON buttons are
Receiver
Receiver
input source
TV power on
transmitted from the remote control unit
power on switched to
TV/DBS
approximately once every second.
Receiver
Receiver Video (VCR) Video (VCR) The signals for the other buttons (DVD,
input source
TV power on
switched to
power on power on playback
VDP, TV / DBS, VCR-1 and CD) are
VCR-1
transmitted approximately once every
Receiver
Receiver input source
switched to 1.5 seconds.
power on
CD
Press the system call button.
• The LEARNED/TX LED flashes for 5
seconds.
Stored Stored Stored Stored
operation 7 operation 8 operation 9 operation 10
1
RC-904
START LEARNED/TX
SYSTEM CALL POWER
SET CALL OFF ON / SOURCE
DVD VDP TUNER SHIFT
1 2 3
2 TV/DBS PHONO
4 5 6
VCR-1 CD CDR / TAPE CHANNEL
7 8 9
VCR-2/V.AUX
TV/VCR
+10 0 A / B
VOLUME DISC SKIP+
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
AUDIO CD MULTI MUTING
AVR/AVC VIDEO DVD TV
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
ENTER
MODE PTY
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
USE/LEARN T.TONE MULTI SET UP