Safety Precaution; Installation Instructions; Use And Maintenance - DeLonghi 3LIK0255 Manual De Utilización

ENGLISH
GENERAL
Carefully read the following important information regarding installa-
tion safety and maintenance. Keep this information booklet accessible
for further consultations. The appliance has been designed for use in
the ducting version (air exhaust to the outside – Fig.1B), filtering ver-
sion (air circulation on the inside – Fig.1A) or with external motor
(Fig.1C).

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously with an
open fireplace or burner that depend on the air in the environment and
are supplied by other than electrical energy, as the cooker hood re-
moves the air from the environment which a burner or fireplace need
for combustion. The negative pressure in the environment must not
exceed 4Pa (4x10-5 bar). Provide adequate ventilation in the environ-
ment for a safe operation of the cooker hood.Follow the local laws
applicable for external air evacuation.
Before connecting the model to the electricity network:
- control the data plate (positioned inside the appliance) to ascertain
that the voltage and power correspond to the network and the socket is
suitable. If in doubt ask a qualified electrician.
If the power supply cable is damaged, it must be replaced with another
cable or a special assembly, which may be obtained direct from the
manufacturer or from the Technical Assistance Centre.
2. WARNING !
In certain circumstances electrical appliances may be a danger
hazard.
A) Do not check the status of the filters while the cooker hood
is operating
B) Do not touch bulbs or adjacent areas, during or straight after
prolonged use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker hood
D) Avoid free flame, as it is damaging for the filters and a fire
hazard
E) Constantly check food frying to avoid that the overheated
oil may become a fire hazard
F) Disconnect the electrical plug prior to any maintenance.
G) This appliance is not intended for use by young children or
infirm persons without supervision
H) Young children should be supervised to ensure they do not
play with the appliance
I) There shall be adequate ventilation of the room when the
rangehood is used at the same time as appliances burning gas
or other fuels
L) There is a risk of fire if cleaning is not carried out in accord-
ance with the instructions
This appliance conforms to the European Directive EC/2002/96, Waste
Electrical and Electronic Equipment (WEEE). By making sure that
this appliance is disposed of in a suitable manner, the user is helping
to prevent potential damage to the environment or to public health.
he symbol on the product or on the accompanying
paperwork indicates that the appliance should not be treated as domestic
waste, but should be delivered to a suitable electric and electronic
appliance recycling collection point.
Follow local guidelines when disposing of waste.
For more information on the treatment, re-use and recycling of this
product, please contact your local authority, domestic waste collection
service or the shop where the appliance was purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out by
specialised personnel.
• Electric Connection
GB
The appliance has been manufactured as a class II, therefore no earth
cable is necessary.
The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral
If not provided, connect a plug for the electrical load indicated on the
description label. Where a plug is provided, the cooker hood must be
installed in order that the plug is easily accessible.
An omnipolar switch with a minimum opening of 3mm between con-
tacts, in line with the electrical load and local standards, must be placed
between the appliance and the network in the case of direct connection
to the electrical network.
• The minimum distance between the support surfaces of the cooking
pots on the cooker top and the lowest part of the cooker hood must be
at least 65 cm.
If a connection tube composed of two parts is used, the upper part must
be placed outside the lower part.
Do not connect the cooker hood exhaust to the same conductor used
to circulate hot air or for evacuating fumes from other appliances gen-
erated by other than an electrical source.
Before proceeding with the assembly operations, remove the anti-
grease filter(s) (Fig.6) so that the unit is easier to handle.
In the case of assembly of the appliance in the suction version prepare
the hole for evacuation of the air.
• If your appliance has been designed for use in habitations supplied
with acentralised suction device perform the following operations:
-The switch controls opening and closure of a valve using a
thermoelectical device. By placing the switch in the ON position, after
a minute, the valve opens rotating 90° allowing suction of the stale air.
By placing the switch in the OFF position, the valve closes after 100
seconds.
• FIXING TO THE WALL
Drill the holes A respecting the distances indicated (Fig.2). Fix the
appliance to the wall and align it in horizontal position to the wall units.
When the appliance has been adjusted, definitely fix the hood using the
screws A (Fig.4). For the various installations use screws and screw
anchors suited to the type of wall (e.g. reinforced concrete, plaster-
board, etc.). If the screws and screw anchors are provided with the
product, check that they are suitable for the type of wall on which the
hood is to be fixed.
• FIXING THE DECORATIVE TELESCOPIC FLUE
Arrange the electrical power supply within the dimensions of the deco-
rative flue. If your appliance is to be installed in the ducting version or
in the version with external motor, prepare the air exhaust opening.
Adjust the width of the support bracket of the upper flue (Fig.3). Then
fix it to the ceiling using the screws A (Fig.3) in such a way that it is
in line with your hood and respecting the distance from the ceiling
indicated in Fig.2. Connect the flange C to the air exhaust hole using a
connection pipe (Fig.4). Insert the upper flue into the lower flue and rest
above the frame. Extract the upper flue up to the bracket and fix it with
the screws B (Fig.3).
To transform the hood from a ducting version into a filtering version,
ask your dealer for the charcoal filters and follow the installation in-
structions.
• FILTERING VERSION
Install the hood and the two flues as described in the paragraph for
installation of the hood in ducting version. To assemble the filtering flue
refer to the instructions contained in the kit.
If the kit is not provided, order it from your dealer as accessory.
The filters must be applied to the suction unit positioned inside the
hood. They must be centred by turning them 90 degrees until the stop
catch is tripped (fig. 7).

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.
It is recommended to leave the appliance in operation for 15 minutes
- 11 -