Publicidad
Idiomas disponibles
Idiomas disponibles
Flash Patterns:
The LED heads can be configured to flash the following patterns (in the order below) by momentarily making contact with the blue
wire and the negative as described in the wiring section. The LED head must be powered through the black and red wires to allow
pattern selection.
Mode
Pattern
P1
ECE R65 120FPM Single Flash P1
P2
ECE R65 120FPM Single Flash P2
P3
ECE R65 Double Flash P1
P4
ECE R65 Double Flash P2
P5
ECE R65 Quad Flash 120 FPM P1
P6
ECE R65 Quad Flash 120 FPM P2
P7
Single Flash 75 (SIM) P1
P8
Single Flash 75 (SIM) P2
P9
Double Flash 75 (SIM) P1
P10
Double Flash 75 (SIM) P2
P11
Quad Flash 75 (SIM) P1
P12
Quad Flash 75 (SIM) P2
P13
OFF.
OPERATE VOLTAGE
DC 10~30V
OPERATE CURRENT
Max. 1.2A
LED COLOUR
Amber
Blue
Red
Amber & Blue
OPERATE TEMPERATURE
-40°C~+ 55°C
MAX. HUMIDITY
60%
PATTERNS
13 FLASH PATTERNS (PER LED COLOUR)
Wire function
Red wire= +VDC: Black wire= -VE: Blue=Pattern
change: Yellow=Synchronize
Tapping timing
Function
0 ~ 1 sec
NEXT PATTERN / ON
1 ~ 3 sec
PREVIOUS PATTERN
3 ~ 5 sec
FACTORY DEFAULT(P1)
OVER 5 sec
OFF
1. Default mode P1
2. The pattern will go to the previous pattern after power off then power on.
3. "SIM" means LED lighthead at the same time " ALT" means LED alternative flash
Manufacturer Limited Warranty and Limitation of Liability:
Manufacturer warrants that on the date of purchase this product will conform to Manufacturer's specifications for this product (which are available from the Manufacturer upon request). This Limited
Warranty extends for Thirty Six (36) months from the date of purchase.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR OTHER HAZARD;
IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER'S INSTALLATION
AND OPERATING NSTRUCTIONS VOIDS THIS LIMITED WARRANTY.
Exclusion of Other Warranties:
MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY, QUALITY OR FITNESS FOR A PARTICULAR
PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE HEREBY
DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.
Remedies and Limitation of Liability:
MANUFACTURER'S SOLE LIABILITY AND BUYER'S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR UNDER ANY OTHER THEORY AGAINST
MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE, AT MANUFACTURER'S DISCRETION, THE REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND
OF THE PURCHASE PRICE PAID BY BUYER FOR NON-CONFORMING PRODUCT. IN NO EVENT SHALL MANUFACTURER'S LIABILITY ARISING OUT OF THIS LIMITED WARRANTY OR
ANY OTHER CLAIM RELATED TO THE MANUFACTURER'S PRODUCTS EXCEED THE AMOUNT PAID FOR THE PRODUCT BY BUYER AT THE TIME OF THE ORIGINAL PURCHASE. IN NO
EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL,
OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A
MANUFACTURER'S REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH
RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR
LIABILITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty defines specific legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction. Some jurisdictions do not allow the exclusion or limitation of incidental
or consequential damages.
Page 2 of 2
P/N 920-5111-00 (Rev C) 2016-12-02
© 2016 at ECCO
Description
R65 Single Flash.
Default Mode
R65 Single Flash.
R65 Double Flash.
R65 Double Flash.
R65 Quad Flash.
R65 Quad Flash.
SAE single Flash.
SAE Single Flash.
SAE Double Flash.
SAE Double Flash.
SAE Quad Flash.
SAE Quad Flash.
APPROVED MOUNTING POSITION TO COMPLY WITH ECE R65 CAT 'HT'
(ONE PAIR OF UNITS AT THE FRONT OR REAR OF VEHICLE)
VEHICLE CENTRAL AXIS
MAX DISTANCE = 10M
APPROVED MOUNTING POSITION TO COMPLY WITH ECE R65 CAT 'T'
(FOUR UNITS MOUNTED ON THE VEHICLE)
MAX DISTANCE = 10M
45º
VEHICLE CENTRAL AXIS
45º
HORIZONTAL PLANE
Center Axis of Lamp
45º
MAX DISTANCE = 10M
45º
ECCO Safety Group Europe
Victoria Industrial Park, Victoria Road
Seacroft, Leeds, England
LS14 2LA
+44 (0)113 2375340
www.eccosafetygroup.com
Publicidad
