Stay Mode; Emergency Call; Mute Mode; Usage Notices - Chacon 34958 Manual Del Usuario

Stay Mode

Input user code or admin code, and press [Stay Mode]
indicator flashes once and the keypad beeps once and sends
Mode] command to the control panel.
When the alarm panel receives the signal, the siren will beep once
and the [Stay Mode] indicator will light on, the alarm system enters
stay mode state.
All the sensors in other zones are armed to prevent the intruder
except that the motion detector in Home Mode Zone is disarmed,
so that people can move freely at home.

Emergency Call

If not inputting code for SOS is set, user just holds the
3 seconds, the LED indicator flashes once, the keypad beeps once,
and the control panel alarms immediately.
Install the keypad away from objects such as heater, air
conditioner, microwave oven etc. that produces heat or
electric-magnetic.
Forbiddance of decomposition
Take the keypad for disposal of recycling according to the local
regulation.
Do not take apart the product if you are not a professional
technician.
Maintenance
You can get most dust or fingerprint off with a dry, soft cloth or
tissue. If there is dirt on the keypad, please wipe the surface by a
soft cloth with a little dilute alkaline detergent and then wipe again
with a dry cloth.
If inputting code for SOS is set, user needs input user code or
admin code before holding the
key, the LED
alarm.
[Stay

Mute Mode

Mute mode means that the LED indicators of control panel flash,
but the siren does not beep, to avoid disturbing the neighborhood.
Input user code or admin code, and hold any key of
[Stay Mode] for 2 seconds, the LED indicator flashes once, the
keypad beeps once and sends corresponding command to the
control panel.
When the alarm panel receives the signal, the LED indicator lights
on or off, but the siren does not beep.
[SOS] key for
FAQ
Problem
Low battery
The positive and
negative terminals
No response are reversed
from keypad
Keypad is locked by
inputting wrong
passcode continually
more than 6 times
No response from
Keypad
alarm panel
cannot
connect to
control panel
Alarm panel beeps
twice
Keypad is not
learned to control
No response panel
from the
control panel
Distance between
by operating
keypad and control
on keypad
panel is too far
[SOS] key for 3 seconds to send an
[Arm] [Disarm]
Cause Solution
Please change the battery
Follow the right terminal
direction and insert the battery
again
Keypad will be unlocked after
non-operation for 20 seconds
Make sure the alarm panel is
powered on
Make sure the alarm panel
enters learning state
Keypad has been learned
Please connect the keypad to
the control panel by following
the manual instruction
Please move the keypad in a
proper distance where control
panel can receive the signal of
keypad
It's recommended to buy signal
repeater to extend the distance
Notices and Maintenance
In order to avoid any harm to the users or others during usage and
prolong the usage life, please abide by the following notices.

Usage Notices

General instruction
The keypad should be connected to control panel before use.
The power supply of keypad will probably impact on the
transmitting distance of wireless signal.
The keypad can be powered by 3 pcs of AAA batteries, or wired
by DC 12V.
The keypad is compatible for any our alarm system.
Please remove the battery insulating strip before use.
Do not press SOS key if there's no emergency to avoid disturbing
the neighborhood..
Check the keypad regularly to ensure the system works properly
in case of emergency.
The keypad is neither waterproof nor moisture-proof, please install
it in a shady, cool and dry place.
The case of keypad is made of ABS. Please keep it away from
strong light to ensure the lifetime..
Forbiddance
The keypad is non explosion-proof. Please keep it away from fire,
flame sources.
The RFID tags are Please connect the RFID tag to
not learned to control panel by following the
keypad manual instruction
Cannot
disarm by Disarm by RFID tag Enter setup state and activate
RFID Tags function is the function of disarm by RFID
deactivated tag
Direct disarm by
Disarm after pressing [*] key
RFID tag is disabled
Keypad is not waked Please input [admin code] + [#]
up to wake up the keypad
Keypad
cannot be
Please input [admin code] +
Keypad doesn't enter
programmed
[#], and press [3] to enter setup
setup state
state
Keypad
cannot be Haven't input user
Please input the user code or
armed, code or admin code
admin code before operation
disarmed and before operation
in stay mode