Sabo BC-30 Manual Del Operador página 27

•
When inserting the new coil, ensure that the thread is in the slot for the new coil. Ensure that the end of the thread extends about 15 cm from the slot.
•
Insert the new coil such that the thread and the slot are aligned to the eye in the thread head. Guide the thread through the eye.
•
Reattach the coil holder by pushing the latches into the slot until the coil holder locks in.
REPLACING THE THREAD
See figure 10
•
Remove the coil from the thread head.
NOTE: Remove any old thread that might possibly still be on the coil.
•
Cut two threads to an approximate length of 3 m.
•
Insert a thread into the anchor hole in the top part of the coil while the other thread is inserted into the anchor hole in the bottom part of the coil.
•
Wind the threads clockwise around the coil as shown by the arrow on the coil.
•
Place the cutting threads into the guide grooves.
•
Fasten the coil protection cover to the coil. Ensure that the end of the cutting thread is pulled out of the groove of the coil protection cover.
•
Insert the springs with the narrow end facing up to the cutting head. Then insert the coil into the cutting head. Insert the ends of the threads through the cutting thread exit holes
in he sides of the cutting head.
•
Replace the cover on the cutting head. Push the cover in until it locks.
STORING THE TRIMMER
•
Remove the battery from the trimmer before storing the device.
•
Store it in a location out of the reach of children.
•
Keep the battery away from the corrosives such as garden chemicals and salt.
•
Keep an unused battery away from paperclips, coins, keys, screws, nails and all other objects that could connect the contacts.
•
A short circuit of the battery can cause burning or fires. Store the battery dry and at a temperature below 27°C.
•
Never store discharged batteries. You must let an excessively warm battery cool before charging.
•
The battery's charge declines during storage. The higher the temperature, the faster the discharge. Recharge the batteries monthly is stored for a longer period. This increases
the life and maintains performance.
•
Remove the battery from the device before adjusting settings, replacing accessories or after use. This prevents the risk of your device being switched on inadvertently or
unsupervised.
•
Secure the trimmer during transport in order to prevent damage and injuries. Clean the device before storage.
ENVIRONMENTAL PROTECTION
•
Environmental protection should be a material and prioritised aspect when using the machine. Do not disturb your surroundings when using the device.
•
Strictly observe the local provisions for disposal of the packaging, oil, petrol, filters, damaged parts or all other polluting materials. These materials must not be disposed of with
domestic waste, but instead must be collected separately and disposed of at a recycling site that recycles the materials.
•
Strictly observe the local provisions for disposal of the cut waste.
If decommissioning the machine, it must not be simply disposed of in the environment, but instead must be disposed of at a recycling site according to the local provisions.
TROUBLESHOOTING
POSSIBLE
PROBLEM
CAUSES
The thread is stuck.
Insufficient thread
on the coil.
Thread is not fed by
the automatic feeder
Thread is worn and
when the trimmer too short.
head is used.
The thread is
wound around the
coil.
Grass winds around High grass is cut
the shaft housing and too close to the
the thread head. ground.
Battery is not locked
in.
Device does not start
Battery is not
charged.
DISPOSING OF THE DEVICE
Do not dispose of electric devices with household waste. Dispose of these devices at recycling centres. Contact the relevant authorities or your retailer for information about this.
Separate collection of used products and packaging allows materials to be recycled. The reuse of materials helps to prevent pollution and reduces the need for raw materials.
Dispose of batteries at the end of their use and consider the environment. The battery contains material that is dangerous to you and the environment. Therefore, it must be
disposed of separately in a facility that accepts lithium-ion batteries.
SPARE PARTS LIST:
•
Handle – SAA12595
•
Grass deflector – SAA12596
•
Spool of thread – SAA12597
SOLUTION
Oil with silicon spray.
Fit more thread. For this, see the section in these instructions about replacing the thread.
Pull the thread while pushing the thread head.
Remove the thread from the coil and wind it up. For this, see the section in these instructions about replacing the thread.
Cut high grass from top to bottom to prevent winding.
To lock in the battery, ensure that the latches on the sides of the battery are locked.
Charge battery according to the instructions supplied with your model.
27