Silverline 633770 Manual Del Usario página 7

633770
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may
affect the power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly
maintained power tools
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous
situation
Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained
Internal Combustion Safety
Dangerous environment
• Do not use petrol tools in damp or wet conditions, or expose them to
rain. Provide adequate surrounding work space and keep area well lit.
Do not use petrol tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gases, or dust of an
explosive nature
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 80dB.
It is the responsibility of the user to ensure that other people exposed to
the noise are also suitably protected
Protect your eyes
• Always wear suitable eye protection
Protect yourself from vibration
• Hand held tools may produce vibration. Vibration can cause disease.
Gloves to keep the operator warm may help to maintain good blood
circulation in the fingers. Hand held tools should not be used for long
periods without a break
Switch off
• Ensure that the engine has stopped before attaching any accessories
to the tool.
• If the tool stops unexpectedly ensure that the power is switched off and
the engine is not running before attempting to check the tool
Running in the engine
• New tools should be used at moderate speed
• Do not maintain high engine speed until the engine is fully run in
• The engine will not be capable of developing maximum power until the
end of the running in period
• When first using the tool, periodically stop and check that all nuts and
screws are securely fastened and tighten them as necessary
• Do not use fuels containing methanol or ethanol, as these may cause
internal damage to the fuel tank and fuel lines
Warning
• Never leave the tool running unattended
• Never leave the machine unattended when parts are still hot
Servicing
• We recommended that your tool is serviced shortly after its first use
• In normal use, have the tool serviced regularly
25cc Multi-Head Garden System
• Do not modify any of the components of this tool. To do so would
invalidate your guarantee, and could result in injury to yourself or others
around you
• Always have your tool serviced at an authorised service centre
Storage
• When you have finished using the tool, clean it completely
• Be careful not to damage the fuel tank, or fuel lines, when it is placed
on the ground
• Ensure that the tool will not be subject to impact damage; any damage
could cause the tool to become unsafe
• Store the tool away from direct sunlight
• Ensure that fuel and oil is stored in a safe place, away from heat, direct
sunlight or any source of ignition
Whenever the machine is likely to be out of use for an extended period of
time, proceed as follows:
• Empty the fuel tank completely
• Protect all metal engine parts from corrosion by coating them with oil
• Remove the spark plug, put a few drops of oil into the cylinder and then
pull the recoil starter 2 to 3 times in order to distribute the oil evenly
• Replace the spark plug
• Never store the machine where children may gain access to it
THIS PRODUCT PRODUCES POISONOUS EXHAUST FUMES AS SOON AS
THE ENGINE IS RUNNING. THESE GASES MAY BE COLOURLESS AND
ODOURLESS. TO REDUCE THE RISK OF SERIOUS OR FATAL INJURY, NEVER
RUN THE MACHINE INDOORS, OR IN POORLY VENTILATED AREAS. ENSURE
PROPER VENTILATION WHEN WORKING IN TRENCHES OR OTHER CONFINED
SPACES.
www.silverlinetools.com
7