First Alert SmartBridge Guia De Inicio Rapido

ENGLISH
DVR QUICK START GUIDE
Product Contents
Power
MENU 1 2 3 4
IR
ESC 1 2 3 4
Rec
DVR
REMOTE CONTROL &
USB 2.0 MOUSE
WARNING
STICKERS
THESE PREMISES ARE UNDER
24 HOUR VIDEO SURVEILLANCE
PROTECTED BY
Remote Software
Installation Disc
Step 1: Connect the DVR to your Monitor or TV
(HDMI or VGA Option) - Connect a HDMI or VGA cord (not included) from your monitor or TV to the
1
HDMI or VGA Output port on the back of your DVR
(BNC Option) - Connect the end of the BNC cable (not included) to the back of the BNC connection
on the DVR labeled "Video Output"
Connect the BNC cable to the BNC input on your TV/Monitor
(Note: If your TV or monitor does not have a BNC connection it is still possible to connect your DVR via the BNC output using a BNC-RCA adaptor
and cable (not included). This may be useful if you decide to connect a monitor or TV via each of the 3 Video out connections from your DVR.)
Turn on your TV/Monitor and select the appropriate input (noted above)
1
1
HDMI VGA
(Note 8 Channel DVR shown. Your connections may be in different areas depending on your DVR model)
Step 2: Connecting the Cameras*
1 Connect both ends of BNC cable from camera to both ends of the 60ft BNC cable labeled
"Camera Side"
Using other side of 60ft BNC cable labeled DVR side, connect BNC to BNC video input on DVR
2
Using the supplied Power splitter Cable, connect the red end to the DVR and one of the black
3
ends to each of the camera's power cables. Connect the single end of the Power splitter Cable
to the power supply.
2
1
Step 3: Powering the DVR*
8 Channel:
POWER SUPPLY*
Connect the DVR to one of the multi-splitter ends
1
DVR & CAMERAS
ETHERNET CABLE
16 Channel:
1 Connect the separately supplied DVR 4 Amp power supply to the DVR
POWER SPLITTER
* 16 Channel DVR systems contain separate power supplies for cameras and DVR
Step 4: Connecting the Mouse and Ethernet Cable
1 Connect the USB mouse to the bottom USB slot on the back
Connect the Ethernet cable to the back of the DVR labeled either NET or RJ45
2
Connect the other end of the cable directly to your router, modem or high speed
3
internet connection input
Note: USB mouse and ethernet cable input locations may vary model to model.
(repeat steps 1-3 for additional cameras)
(Attach for each camera)
(Power Splitter)
3
1
1
(4 Amp)
(3 Amp)
BACK of DVR
2
1
3
REMOTE ACCESS REMOTE ACCESS
Easy Setup
1 Power on the SmartBridge
• Right click anywhere on the screen
and select System Setup
(no password is required until you set one up)
2 Select the Network Tab. Your Unique
Device ID will be listed here.
PC Connect Setup
3
• Insert SmartBridge Remote Software Installation
Disc into your computer or laptop
• Install Software
• Open Program
• Enter Unique System ID into the Device ID prompt,
Password is set to a default 123
• Select "Login" to access your system
Smartphone and Tablet Setup
4
• Download SmartBridge Mobile App
• Open App and enter Unique System ID into the Device ID prompt
• Select "Login" to access your system
Go to firstalert.com to find complete instruction manual for your First Alert DVR.
© 2013 BRK Brands, Inc. All rights reserved. Distributed by BRK Brands, Inc., Aurora, Illinois
60504. Due to continuing product development, the product inside the packaging may look
slightly different than the one on the package. 1 Year Limited Warranty – see inside for details.
BRK Brands, Inc. is a subsidiary of Jarden Corporation (NYSE: JAH).
www.firstalert.com