Battery Pack - Metabo SSE 18 LTX BL Manual Original

en ENGLISH
- Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
5. Overview
See page 2.
1 Lever for setting the guide
2 Guide
3 Saw blade clamping fixture
4 LED working light
5 Lever of the saw blade clamping fixture
6 Front handle
7 Switch on catch button
8 Lock button (continuous operation)
9 Trigger
10 Rear handle
11 Battery pack release button

12 Battery pack

13 Capacity indicator button
10
14 Capacity and signal indicator
6. Assembly, Initial Operation,
Setting
Remove the battery pack from the machine before
any adjustment or maintenance is carried out.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
6.1 Battery pack
Charge the battery pack before use (12).
If performance diminishes, recharge the battery
pack.
"Li-Power" li-ion battery packs have a capacity
and signal indicator: (14)
- Press the (13) button, the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removal:
Press the battery pack release (11) button and pull
the battery pack (12) forwards.
Inserting:
Slide in the battery pack (12) until it engages.
6.2 Inserting, removing saw blade
Do not touch the saw blade immediately
following operation of the tool, as it can be
extremely hot and can lead to skin burns.
1 Pull up lever (5) of saw blade quick-clamping
device upwards and hold in this position.
2 Insert the saw blade as far as it will go or remove
it.
3 Release lever (5).
4 Check that the saw blade is securely seated.
6.3 Setting the guide
The cutting depth can be limited by shifting the
guide (2) (e.g. when sawing in front of a wall).
Occasionally shift the guide (2) to achieve even
wear of the saw blade.
1. Swivel the lever (1) downwards and shift the
guide (2) to the desired position. See image
series B
2. Swivel the lever (1) upwards and turn the guide
(2), if needed, until the lever engages again.
Check the guide (2) to ensure that it is securely
fitted. It has to be engaged.
7. Use
7.1 Switching on and off, stroke rate,
Switch-on lock (7):
Trigger (9) locked.
Trigger (9) unlocked.