AKG Acoustics IVM4 Modo De Empleo página 30

L
I I m m p p o o r r t t a a n n t t ! !
N N o o t t e e : :
3 3 . . 1 1 C C o o l l o o r r C C o o d d i i n n g g
3 3 . . 1 1 . . 1 1 T T r r a a n n s s m m i i t t t t e e r r
Refer to fig. 7.
3 3 . . 1 1 . . 2 2 R R e e c c e e i i v v e e r r
Refer to fig. 8.
3 3 . . 2 2 P P l l a a c c i i n n g g t t h h e e
T T r r a a n n s s m m i i t t t t e e r r
3 3 . . 3 3 R R a a c c k k M M o o u u n n t t i i n n g g t t h h e e
T T r r a a n n s s m m i i t t t t e e r r
3 3 . . 3 3 . . 1 1 R R a a c c k k M M o o u u n n t t i i n n g g a a
S S i i n n g g l l e e T T r r a a n n s s m m i i t t t t e e r r
Refer to fig. 9.
3 3 . . 3 3 . . 2 2 R R a a c c k k M M o o u u n n t t i i n n g g
T T w w o o T T r r a a n n s s m m i i t t t t e e r r s s
S S i i d d e e b b y y S S i i d d e e
Refer to fig. 10.
30
3 Setting Up
• Prior to every soundcheck, verify that the transmitter and receiver are
tuned to the same frequency.
• The adjustment procedures for all transmitter and receiver parameters are dia-
grammatically shown in figs. A1 to A25 on pages 122 through 136.
• If you use several IVM 4s simultaneously, mark the transmitter and receiver of
each channel with the same color.
1. Use a small screwdriver or similar object to lever the color code ring out of its
seat.
2. Align the pins and positioning lug on the rear of the new color code ring with the
corresponding openings on the transmitter and push the color code ring home.
1. Open the battery compartment (1).
2. Remove the color code cover (2) and remove the color code paper strip.
3. Remove the desired new paper strip (3) from the color code sheet and place the
paper strip (3) in the groove in the transmitter body.
4. Replace the color code cover (2).
5. Close the battery compartment (1).
Reflections off metal parts, walls, ceilings, etc. or the shadow effects of musicians
and other people may weaken or cancel the direct transmitter signal.
For best results, place the transmitter or remote antenna as follows:
1. Place the transmitter/antenna near the performance area (stage). Make sure,
though, that the receiver will never get any closer to the transmitter than 10 ft
(3 m). Optimum separation is 16 ft. (5 m).
2. Place the transmitter/antenna at least 5 ft. (1.5 m) away from any big metal ob-
jects, walls, scaffolding, ceilings, etc.
3. Place the transmitter at least 10 ft. (3 m) away from any wireless microphone re-
ceiver (e.g., an SR 4000) in order to prevent crosstalk from the in-ear monitor
system into wireless microphone channels.
1. Unscrew the four rubber feet (1) from the transmitter bottom panel.
2. Unscrew the two fixing screws (2) from each side panel.
3. Use the fixing screws (2) to screw the short bracket (3) to one side panel and the
long bracket (4) to the other side panel. The brackets are contained in the sup-
plied rack mounting kit.
4. Install the transmitter in your rack.
1. Unscrew the four rubber feet (1) from each transmitter's bottom panel and re-
move the screws (5) from the rubber feet (1).
2. Unscrew the two fixing screws (2) from the right-hand side panel of one trans-
mitter and from the left-hand side panel of the other transmitter.
3. Remove the plastic covers (3) from the side panels with the fixing screws (2) still
on.
4. Insert one connecting strip (4) into each free slot in the side panel of the first
transmitter, making sure to align the hole in each connecting strip (4) with the ap-
propriate threaded hole in the transmitter bottom panel.
5. Fix the three connecting strips (4) on the first transmitter using three of the
screws (5) you removed from the rubber feet.
6. To join the two transmitters, slide the connecting strips (4) on the first transmit-
ter through the free slots in the side panel of the second transmitter. Make sure
to align the hole in each connecting strip (4) with the appropriate threaded hole
in the bottom panel of the second transmitter.
7. Fix the connecting strips (4) on the second transmitter using the three screws
(5) you removed from the rubber feet.
8. Screw a short bracket (6) to the outer side panel of each transmitter using for
each bracket two of the screws (2) you removed from the transmitter side pan-
els.
9. Install the transmitters in your rack.
AKG IVM 4