Listening To The Fm Radio; Listening To The Ipod - Billiger S Manual Del Usuario

How to adjust volume and sound?
1. Use the , , ,
control (or the touch panel wheel for the volume only) to adjust
sound and volume.
2. Volume: 0 means silence, 100 means maximum output.
3. Treble and Bass: -6 means very little Bass or Treble, 0 means
neutral, 6 means maximum effect.
4. If you turn the device off, the current values are stored.
How to mount the stand?
The cabinet can be mounted on the enclosed stand. To mount the
stand, proceed in two steps:
1. Remove the feet from the cabinet (simply pull them off the
bottom plate).
2. Assemble the stand tube and plate and attach it to the cabinet
bottom plate
.
1.

2. Listening to the iPod

Step 1. To use the Geneva Sound System with an iPod, select
iPod as the audio source using the
automatically open and the display under the grille should display
"no iPod".
Step 2. Insert the correct iPod adapter: Attach the Dock Adapter
to the iPod Universal Dock by pressing lightly on the top of the
Dock Adapter (see picture) and it will snap in:
How to select the right iPod adapter for my iPod?
Use the iPod adapter provided with your iPod. Only if an
iPhone has to be docked, use the iPhone adapter provided
with the Geneva Sound System.
Step 3. Insert the iPod into the iPod dock. The display should now
show „iPod".
Step 4. Press the key on the remote control or on the touch
panel. If you still cannot hear any sound check that the volume is
turned up by adjusting the
, , keys on the remote
2.
key: the iPod dock will
key or the wheel.
Step 5. You can control your iPod using the
on your remote control and on the touch panel.
Step 6. Use the key and the wheel on the touch panel to
browse the iPod. A menu entry on the iPod is selected by tapping
the wheel.
Charging: Your iPod is charging while the system is connected to
an AC plug.

3. Listening to the FM radio

Step 1. Select FM radio as the audio source using the
on the remote control or on the touch panel; the display under the
grille should display an FM frequency, e.g. "103.2". If you cannot
hear any sound, check the volume setting by pressing the
Step 2. Select an FM station with the
increases or decreases the frequency by 100 kHz. The number on
the display under the grille indicates the current frequency in MHz
(e.g. "88.7" on display means 88.7 MHz). Hold down the
the key and the FM radio will search for the next station au-
tomatically. When a station has been found, the automatic search
stops. To keep scanning, repeat this action.
How to switch between mono and stereo?
Press the button for 1 second to toggle between mono and
stereo mode.
How to store / recall a radio station (presets)?
1. Select your favorite radio station using the
the remote control or on the touch panel.
2. Select one of the 6 preset keys on the remote control, and keep
pressing it until the corresponding letter on the display starts
blinking. The station has now been stored and can be recalled by
pressing the same preset key.
How to erase or overwrite a preset?
Stored presets do not need to be erased - just use the previous
steps to store a new station in a preset.
4. Listening to the DAB radio
(Model S DAB only)
The DAB radio is operated exactly like the FM radio, with the follo-
wing differences:
1. A scanning operation has be done the first time the unit is
installed or when the unit is moved to a different location: the
scanning procedure is started by holding down the
least 3 seconds (while in DAB mode): the „SCANNING"
message will pop-up on the display. The scanning procedure
could take up to a minute to complete.
2. Radio station names are displayed instead of frequencies.
To browse the DAB stations list use the
remote control or on the touch panel.
About the presets usage, please refer to the FM radio section.
5
, , keys
key on
key.
and keys: one click
or
or keys on
key for at
and keys on the