WOOD'S AC Milan Silent 7K Manual De Instrucciones página 13

FUNCTION OF THE OPERATION MODES AND INSTALLATION DESCRIPTIONS
A. Accessories
After unpacking, please check whether
the above-mentioned accessories are
included, and check their purposes in
the installation introduction in this
manual.
B. Mobile air conditioner
J. Appearance and Function of Remote
Control.
Notes:- Do not drop the remote control.-
Do not place the remote control in a
location exposed to direct sunlight.
A. Operation Introduction
Before starting operations in this section:
1) Find a place where there is power
supply nearby.
2) Install the exhaust hose, and adjust
the window position well.
3) Connect drain hose well (only for using
heating model);
4) Insert the power cord into an grounded
AC220~240V/50Hz socket;
5) Press the POWER button to turn on
the air-conditioner.
K&L. Introduction to Exhaust Hose
Installation
M) Temporary installation
1.Twist both ends of the exhaust hose
into the Hose Connector.
2.Insert the square fixing clip into air
outlet at back of the air conditioner
3.Put the other end of the exhaust hose
to the near windowsill.
N. Window Slider Kit Installation
The installation manner of window slider
kit is mostly in "horizontal" and
"vertical". As shown Fig.5 and Fig.5a,
check the min. and max. size of the
window before the installation.
1. Install the window kit on the window ;
2. Adjust the length of the window slider
kit according to the window width or
height, and fix it with the dowel;
3. Insert the Window connector hose to
the hole of the Window kit.
O. Internal Tank Water Full Alarm
Function
The inner water tank in the airconditioner
has one water level safety
switches, it controls water level. When
water level reaches an anticipated
height, the water full indicator lamp
lights up. Error code "E4" will show on the
display. (If water pump is damaged,
when the water is full, please remove
the rubber blockage at the bottom of
unit, and all water will be drained
outside.)
It is very important that the filter is
cleaned regularly; otherwise the
air conditioner might lose capacity
and even be seriously damaged.
H. Maintenance Explanations
Declaration:
1) Before cleaning, be sure to
disconnect the unit from any electric
supply outlet;
2) Do not use gasoline or other
chemicals to clean the unit;
3) Do not wash the unit directly;
4) If the conditioner is damaged,
please contact the dealer or repair
shop.
1. Air Filter
-If the air filter becomes clogged with
dust/dirt, the air filter should be
cleaned once every two weeks.
-Dismounting
Open the air inlet grille and take off air
filter.
-Cleaning
Clean the air filter with a neural
detergent in lukewarm ( 40°C ) and let
dry in the shade.
-Mounting
Putting the air filter into the inlet grille,
replace the components as they were.
2. Clean the Air-conditioner Surface
First clean the surface with a neutral
detergent and wet cloth, and then
Operating Instructions
wipe it with a dry cloth.
E. Before using
Check up whether the exhaust hose
has been mounted properly.
Cautions for cooling and
dehumidifying operations:
-When using functions on cooling and
dehumidifying, keep an interval of at
least 3 minutes between each
POWER.
-Power supply meets the
requirements.
-The socket is for AC use.
-Do not share one socket with other
appliances.
-Power supply is
AC220-240V, 50Hz
1. Turn on the unit
a) Plug in, then the unit beeps once, " "
The power indicator light is on.
b) Press the " " button, then the unit is
turned on.
c) The LED displays the room temperature
and under Automatic mode.
2. Cooling operation
-Press the "Mode" button till the
"Cool" icon appears.
+ -
-Press the " "or" "button to select
a desired room temperature.
(15°C -31°C )
-Press the "Fan Speed" button to
select wind speed.
3. Dehumidifying operation
Press the "Mode" button till the
"Dehumidify" icon appears .
-Automatically set the selected
temperature to current room
temperature minus 2°C .
-Automatically set the fan motor to
LOW wind speed.
4. Fan operation
-Press the "Mode" button till the "Fan"
icon appears.
-Press the "Fan Speed" button to
select wind speed.
5. Heating operation (this function is
not available for a cold-single unit)
-Press the "Mode" button till the
"Heat" icon appears.
a desired room temperature.
GB
13