Resumen de contenidos para PRETUL MOG-65P
- Página 1 Manual Gasoline 6.5 Hp / 13 Hp Engine Power Applies for: Codes Models 28114 MOG-65P 28115 MOG-130P Read this manual thoroughly CAUTION before using the tool.
-
Página 2: Tabla De Contenido
Assembly Keep this manual for future references. Fuel and Oil The illustrations in this manual are for reference Start Up only. They might be different from the real tool. Maintenance Troubleshooting Notes Authorized Service Centers Warranty Policy MOG-65P MOG-130P ENGLISH... -
Página 3: Technical Data
Technical Data MOG-65P MOG-130P Code 28114 28115 Description Gasoline Engine Motor Cylinders 196 cm (cc) 389 cm (cc) Motor Rated Power 6.5 Hp 13 Hp Max. Torque 11.8 Nm 25 Nm Diameter / Type shaft 3/4” whit keyseat 1” whit keyseat... -
Página 4: General Safety Warnings For Motor Tools
General Safety Warnings for Motor Tools Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. These safety gears reduce the risk Never use the tool in explosive areas or in the presence of injury. -
Página 5: Safety Warnings For Gasoline Engines
Safety Warnings for Gasoline Engines Fuel Handling • Never smoke close to where there is fuel, nor the filling up zone or when operating the pump. • To reduce risk of fire or burns, handle fuel with care. It is extremely flammable. •... -
Página 6: Parts
Parts Fuel Tank Cap Exhaust Fuel tank Filter Spark Plug Oil Supply Shaft Oil Drain Cap Throttle Choke Lever Start Knob Fuel Key Starter jack-line Supply Oil Drain Cap ENGLISH... -
Página 7: Assembly
Assembly Engine mount • The motor must be attached to a plate (A) welded to the structure or chassis of the machine where the engine will be housed. This plate must be larger than the base of the engine and have four perforations to fix the motor with four sets of hexagonal bolts. -
Página 8: Fuel And Oil
Fuel and Oil Oil Supply (A) Fuel Supply (B) • Set the equipment onto a flat and leveled surface. • Set the Pressure Washer on a flat and leveled surface. • Turn and remove the oil supply cap. • Clean and dry the area around the fuel cap. •... -
Página 9: Start Up
Start Up Start Up CAUTION Before starting the pump some topics need to be taken care of. Otherwise it can get damaged and the Warranty cancelled: • All the hoses shall be disconnected, totally untangled and with no kinks. • Water supply shall be connected and fully open. •... -
Página 10: Maintenance
Maintenance CAUTION • Regular and careful maintenance is • Any worn or damaged part shall be replaced before essential to maintain the safety levels and the optimal using the equipment. Do not try to repair the parts. It can performance of the equipment. damage the equipment and become a risk to your safety. -
Página 11: Fuel Filter
Maintenance Fuel Filter Spark Plug • The fuel filter stops water or dirt present in the fuel • Before removing the spark plug (B), wipe clean the area tank to enter into the carburetor. around the spark plug base to stop dust and debris If the motor has not been run after a long period of time, entering the motor. -
Página 12: Troubleshooting
Troubleshooting Problem Cause Solution Motor does not start. • The switch is OFF. • Turn ON the switch. • Not enough fuel. • Fill up fuel tank. • Oil level is too low or there is no oil. • Check oil level as indicated in page 8. •... -
Página 13: Notes
Notes ENGLISH... - Página 14 Notes ENGLISH...
-
Página 15: Authorized Service Centers
Authorized Service Centers In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 0187-8737 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS AGUASCALIENTES... -
Página 16: Warranty Policy
Codes Models Brand 28114 MOG-65P 28115 MOG-130P This product is guaranteed for 1 year. To make the warranty valid or purchase parts and components you must present the product in Corregidora 22, Col. Centro, Alc. Cuauhtémoc, CDMX C.P. 06060 or at the...