Clicker CLK1 Guia De Inicio Rapido página 2

If you did not have any remotes and you set a 9 digit random code and you have
a yellow, white or gray smart-learn button, press the smart-learn button and
release it. Enter your 4-digit pin number and hold any additional number, the door
should operate. Programming is complete.
2 GREEN LEARN BUTTON
3 ORANGE/RED LEARN BUTTON
SYSTEMS WITH SMART-LEARN BUTTON
Locate your smart-learn button on your system. It will be located on the side or
back panel of the motor unit (near the small grey wire antenna).
The original hand held remote will not have code switches.
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
Write PIN here:
Before initial programming, press ✽ and # together
AVERTISSEMENT
until keypad stops flashing. This erases previous
programming and returns unit to unprogrammed factory setting. When
programming to more than one door, do not clear keyless after a successful
programming of the first door.
AVERTISSEMENT
Door 1, Enter 1 2 3 4 and the ✽ key.
Step 1
or Door 2, Enter 5 6 7 8 and the ✽ key.
Enter your PIN and the ✽ key.
Step 2
Step 3 Enter your PIN and the # key.
Step 4 GREEN LEARN BUTTON Enter 2 and the # key.
or ORANGE LEARN BUTTON Enter 3 and the # key. Wait 10 seconds.
Step 5 Press and release smart-learn button on motor unit. (indicator light
next to smart-learn button should turn on.)
Step 6 Enter your PIN into the keypad.
Step 7 Press and HOLD any additional number on the keypad until the
indicator light next to the smart-learn button blinks.
Note: Do not use the ✽ or # keys as a 5th number.
Programming is complete. Wait 10 seconds.
Once programmed, the keypad remains active for 15 seconds. During this time you
may stop, reverse or reactivate the door by pressing any number on the keypad.
To test enter PIN followed by any 5th additional number.
Note: Do not use the ✽ or # keys as the 5th number.
4 LINEAR AND MOORE-O-MATIC
Locate your systems code switch positions from an original hand held remote or
the motor unit receiver. If the switch is "on" or "up", place a 1; "off" or
"down", place a 2 in the corresponding box in the TABLE below.
1 2 3 4 5 6 7 8
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
Write PIN here:
Before initial programming, press ✽ and #
together until keypad stops flashing. This erases
previous programming and returns unit to unprogrammed factory setting.When
programming to more than one door, do not clear keyless after a successful
programming of the first door.
Door 1, Enter 1 2 3 4 and the ✽ key.
Step 1
or Door 2, Enter 5 6 7 8 and the ✽ key.
Enter your PIN and the ✽ key.
Step 2
Step 3 Enter your PIN and the # key.
Step 4 Enter 4 and the # key.
Step 5 Enter code in sequence from the TABLE above and the # key.
Programming is complete.
To test enter PIN followed by any 5th additional number.
Note: Do not use the ✽ star or # pound keys as a 5th number.
If programming is unsuccessful:
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation. Linear and Multi-Code are Trademarks of Linear
Corporation. Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Do It is a Trademark of Do It Best Corporation.
114A2517C
WARNING
WARNING
PROGRAMMING
PROGRAMMING
TECHNICAL SUPPORT: 800-442-1255
(MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM)
©2004, Clicker Corporation
5 GENIE (9 CODE SWITCH SYSTEMS)
6 GENIE (12 CODE SWITCH SYSTEMS)
Locate your systems code switch positions from an original hand held remote or
the motor unit receiver. If the switch is "on" or "up", place a 1; "off" or "down",
place a 2 in the corresponding box in the TABLE below.
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
Write PIN here:
Before initial programming, press ✽ and #
together until keypad stops flashing. This erases
previous programming and returns unit to unprogrammed factory setting. When
programming to more than one door, do not clear keyless after a successful
programming of the first door.
Door 1, Enter 1 2 3 4 and the ✽ key.
Step 1
or Door 2, Enter 5 6 7 8 and the ✽ key.
Enter your PIN and the ✽ key.
Step 2
Step 3 Enter your PIN and the # key.
Step 4 GENIE (9 Code Switch Systems) - Enter 5 and the # key.
or GENIE (12 Code Switch Systems) - Enter 6 and the # key.
Step 5 Enter code in sequence from the TABLE above and the # key.
Programming is complete.
To test enter PIN followed by any 5th additional number.
Note: Do not use the ✽ star or # pound keys as a 5th number.
If programming is unsuccessful:
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
7 MULTI-CODE • 8 STANLEY
Locate your systems code switch positions from an original hand held remote or
the motor unit receiver. If the switch is "on" or "up", place a 1; "off" or "down",
place a 2 in the corresponding box in the TABLE below.
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
Write PIN here:
Before initial programming, press ✽ and #
together until keypad stops flashing. This erases
previous programming and returns unit to unprogrammed factory setting. When
programming to more than one door, do not clear keyless after a successful
programming of the first door.
Door 1, Enter 1 2 3 4 and the ✽ key.
Step 1
or Door 2, Enter 5 6 7 8 and the ✽ key.
Enter your PIN and the ✽ key.
Step 2
Step 3 Enter your PIN and the # key.
Step 4 MULTI-CODE - Enter 7 and the # key.
or STANLEY - Enter 8 and the # key.
Step 5 Enter code in sequence from the TABLE above and the # key.
Programming is complete.
To test enter PIN followed by any 5th additional number.
Note: Do not use the ✽ star or # pound keys as a 5th number.
If programming is unsuccessful:
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
• Stanley brands try as Multi-Code, Multi-Code brands try as Stanley.
All Rights Reserved
1 2 3 4 5 6 7 8 9 10 11 12
PROGRAMMING
1 2 3 4 5 6 7 8 9 10
PROGRAMMING
Printed in Mexico