Clicker CLT 1 Guia De Inicio Rapido página 2

Control remoto universal para abridor de puerta de cochera
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

SECTION I
Determine if your motor unit/receiver system has DIP switches or a smart-learn button.
(Locate the small gray wire antenna. Some
models require removing the light lens.)
• If the Receiver has 9 DIP switches Proceed to TYPE A
• If the Receiver has a yellow, white, or gray smart-learn button, proceed to TYPE B
• If the Receiver has a green, red, or orange smart-learn button, proceed to TYPE C
The Receiver DIP switch has three positions labeled "+", "0"
TYPE
and "-". The "0" setting cannot be used with the clicker remote.
A
1) Reset switches: 1 to "-" and positions 2 through 9 to a random
setting using "+" and the "-". DO NOT USE THE "O" SETTING.
2) Gather any existing remotes and open to expose the DIP switches. Reset
the DIP switch to match the newly coded receiver. Note: some three button remotes do
not have a #1 switch. Match the 2 through 9 to the receiver. On three button remotes
the large button is now programmed to activate the door. 3) Test all the newly coded
remote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING.
After determining that the Receiver has a yellow, white or gray
TYPE
learn button, 1) Gather any existing remotes and open to expose
B
the DIP switches labeled "+", "0" and "-". 2) Reset switches: 1 to
"-" and positions 2 through 9 to a random setting using "+" and
the "-". DO NOT USE THE "0" SETTING, SET ALL REMOTES
TO THE SAME SETTING. On three button remotes the large button is
now programmed to activate the door. 3) The recoded remotes must be
programmed to the receiver. Press and release the smart-learn button.
Then press and hold the existing remote push button for three seconds.
4) Test all the newly coded remote controls to be sure that they operate the
door before proceeding to the BRAND MODE SETTING.
TYPE
With this type receiver, the existing remotes do not contain DIP switches.
Proceed to BRAND MODE SETTINGS.
C
BRAND MODE SETTINGS
FOR TYPE A AND B
Step 1
ON
ON OFF OFF
Existing
Remote
Match
existing codes.
Set extra
switches off.
Step 2
Step 3
Step 4
Step 5
A. Press and release
1
2
3
KG
KG
Step 6
-
Programming is complete, to test, press the button selected to activate garage door.
-
Chamberlain, Sears, LiftMaster, Master Mechanic, DoIt
O
DIP SWITCHES
Clicker
Remote
Continue to Step 2.
-
Press and hold both buttons for 5 seconds or until LED begins to flash.
-
When LED flashes, release both buttons.
-
Press the button you wish to operate the opener (your choice).
For type A & B, proceed to step 6. For type C, continue on to Step 5.
Smart-Learn
button.
- Set switches on clicker remote
FOR TYPE C
GREEN SMART-LEARN
BUTTON
ON
ON ON OFF
– OR –
ORANGE/RED
SMART-LEARN BUTTON
OFF ON
ON OFF
B. Press and hold button
selected in Step 4 for 3 seconds.
1
2
KG
SMART-LEARN
BUTTON
1 2 3 4
RANDOM 2-9
O
DO NOT USE
1 2 3 4
RANDOM 2-9
O
DO NOT USE
1
2
3
KG
KG
- Step 1
3
KG
5
6 7 8 9
Use this
button
5
6 7 8 9
Remote
push button
Use this
button
Code switch
settings are
not used.
Code switch
settings are
not used.

Publicidad

Tabla de contenido
loading

Tabla de contenido