Moog SM5C8N Instrucciones De Instalación Y Funcionamiento
  1. Manuales
  2. Marcas
  3. Moog Manuales
  4. Cámaras de Seguridad
  5. SM5C8N
  6. Instrucciones de instalación y funcionamiento
Moog SM5C8N Instrucciones De Instalación Y Funcionamiento

Moog SM5C8N Instrucciones De Instalación Y Funcionamiento

Ocultar thumbs
Tabla de contenido

Publicidad

Enlaces rápidos

Descargar este manual
SM5C8N
PoE Ready
5"Compact Vandal Resistant, Surface Mounted Dome Camera Enclosure
™
SM5C8N......... Outdoor 5" PoE surface mount housing for small PTZ camera, conduit input from the side and top of the housing, 30W PoE input, with heater
(SM5T8N)
and Dynamic Power Allocation
SM5CF8N....... Outdoor 5" PoE surface mount housing for small fixed camera, conduit input from the side and the top of the housing, 30W PoE input, with
(SM5TF8N)
heater and Dynamic Power Allocation. Polycarbonate body and clear / tinted dome. IP66, 1" NPT threads for pendant mount.
SM5CF8NE......Outdoor 5" PoE surface mount housing for small fixed camera, conduit input from the side and the top of the housing 30W PoE input, with
(SM5TF8NE) heater and Dynamic Power Allocation. Polycarbonate body and clear / tinted dome. IP66, 1" NPT threads for pendant mount.
(no midspan included)
SM5C8NE....... Outdoor 5" PoE surface mount housing for small PTZ camera, conduit input from the side and the top of the housing 30W PoE input, with
(SM5T8NE)
heater and Dynamic Power Allocation. Polycarbonate body and clear/tinted dome. IP66, 1" NPT threads for pendant mount.
(no midspan included)
Substitute "C" (Clear dome) for "T" (Tinted dome) version
© 2013, Moog Inc. All Rights Reserved
. Polycarbonate body and clear/tinted dome. IP66, 1" NPT threads for pendant mount.
™
Moog Inc.
Sensor and Surveillance Systems
Installation and Operation Instructions
Before attempting to connect or operate this product, please
read these instructions completely.
81-IN5460 111313

Publicidad

Tabla de contenido
loading

Manuales relacionados para Moog SM5C8N

Resumen de contenidos para Moog SM5C8N

  • Página 1 5”Compact Vandal Resistant, Surface Mounted Dome Camera Enclosure ™ SM5C8N..Outdoor 5” PoE surface mount housing for small PTZ camera, conduit input from the side and top of the housing, 30W PoE input, with heater (SM5T8N) and Dynamic Power Allocation .

  • Página 2: Important Safeguards

    IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. Keep these instructions. CAUTION Heed all warnings RISK OF ELECTRIC SHOCK DO NOT OPEN Follow all instructions. Do not use this apparatus near water. CAUTION: TO REDUCE THE RISK OF Clean only with damp cloth. ELECTRIC SHOCK, DO NOT REMOVE COVER ( OR BACK).
  • Página 3 ™ During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Manufacturer at Moog Decatur Operations, 2525 Park Central Boulevard, Decatur, Georgia, 30035. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip.

  • Página 4: Electrical Specifications

    Electrical Specifications Contents of Box Power POE 56V SM5C8N SM5CF8N Input Power: 100 to 240VAC (Midspan) Power: 0.8A Frequency: 50 to 60 HZ output Camera: POE (55VDC) Heater: 56VDC (max. 20W) English (1) Mounting Plate Energía de entrada: 100 a 240VAC (Midspan) Energía: 0.8A...
  • Página 5 For Surface Mounting Using Side Conduit Entrance PACKETS (1) Mounting Plate (1) 1/4 x 20 Bolt (1) 1/4 Flat Washer (1) 1/4 Lock Washer (4) M3 6mm Bolt (4) M3 Lock Washers (7) 8 x 32 x 3/8" bolts (2) 8 x 32 Nuts (2) 94-FSCT01 Fixed Etch knockout slightly with utility knife.
  • Página 6 For Surface Mounting Using Side Conduit Entrance Continued For Surface Mount Applications WARNING: Ensure drill is level to avoid damage to the circuit board Mount securely to ceiling or mounting Drill out (3) mounting holes as shown for # 10 surface using the appropriate hardware hardware (not supplied) •...
  • Página 7 For Pendant Or Wall Mount Applications For Pendant Or Wall Mount Applications Seal pipe threads with teflon tape supplied Thread housing to optional pendent pipe with outdoor housings. or wall mount bracket • Hilos de rosca de pipa del sello con la cinta del Teflon •...
  • Página 8 Arecont AV1315 / AV2815 / AV2805 / AV10005 Camera REMOVE Remove center section from fixed camera bracket. Attach to mounting plate with hardware provided. Secure and complete wiring connections. • Quite la sección de centro del soporte fijo de la cámara. Ate a la pletina con el hardware proporcionado. Asegure y termine las conexiones del cableado.
  • Página 9 Axis 212 PTZ Camera ½" 2" Remove center section from fixed camera bracket. Attach to mounting plate with hardware provided. Secure and complete wiring connections. • Quite la sección de centro del soporte fijo de la cámara. Ate a la pletina con el hardware proporcionado. Asegure y termine las conexiones del cableado.
  • Página 10 Panasonic BB-HCM381 / KX-HCM280A Camera Use this hole ½" pattern Secure camera quick release Install (4) .5” spacers to Tighten hardware and plate to mounting plate with center bosses. complete wiring. #8 hardware provided. • Placa segura del lanzamiento rápido de la •...
  • Página 11 Panasonic WV-NF284 / WV-NF302 Camera 1" Secure camera quick release Install (4) 1” spacer to Secure camera safety screw. mounting plate with #8 center bosses. hardware provided. • Pletina segura del lanzamiento rápido de la • Instale (4) 1” espaciador para centrar los •...
  • Página 12 Toshiba IKWB21A Camera ½" 1" Secure camera quick release Tighten hardware and 1” spacers + (4) .5” spacers mounting plate with ¼” hardware complete wiring. (4) corner bosses. provided. • 1” espaciadores + (4) jefes de la esquina de • Pletina segura del lanzamiento rápido de la cámara •...
  • Página 13 Press the Calibration button for one second. Both the Test and Heat LED will turn ON. Once the unit has been Reset successfully calibrated, the Test and Heat LED will turn OFF. Once this is complete the Heat LED will turn ON only if the heater is ON.
  • Página 14 Install security screw, if desired Attach lanyard loop to hook • Instale el tornillo de la seguridad, si está deseado • Ate el lazo del acollador al gancho • Installez la vis de sécurité, si désiré • Attachez la boucle de lanière au crochet •...

  • Página 15: Replacement Parts List

    Replacement Parts List Item Part Comments Number Number Replace Trim Ring Assembly RP0SM5TR Dome and Gasket RPDC5 RP40VL3586 SM5 Housing RP95FSP01 1” NPT Plug Blower RPBACH8N RP762010 POE SM5 PCB Heater for POE Housing RPHACH8N RPVL3790 Heater Bracket RP70VL9001G 30Watt Midspan...

Tabla de contenido