Ingersoll Rand IRGOPIC DB 10 Serie Manual De Uso Y Mantenimiento página 23

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

PART NUMBER FOR ORDERING
Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . DT10–A674
*
Warning Label
for –EU models . . . . . . . . . . . . . . . . . EU–99
for all other models . . . . . . . . . . . . . . WARNING–6–99
39
Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DT10–674
39A
Exhaust Baffle . . . . . . . . . . . . . . . . . . . . . DT10–674Y
40
Outer Lower Bushing . . . . . . . . . . . . . . . . . . DT10–209X
41
Front End Cap . . . . . . . . . . . . . . . . . . . . . . . . DT10–303
42
O–ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DT10–103
43
Retaining Pin (for Fronthead–type Retainers) . . DT10–242Y
45
Screw–on Retainer
7/8" x 3 1/4"
(22 x 82 mm) hex shank . . . . . . . . . . DT9–22–1/3
22 x 70 mm round shank . . . . . . . . . . DT9–22–4/5
23 x 70 mm round shank . . . . . . . . . . DT9–22–4/5
25 x 75 mm round shank . . . . . . . . . . DT9–22–1/3
26 x 70 mm round shank . . . . . . . . . . DT9–22–6
46
Fronthead (bare)
for 22 x 70 mm round shank . . . . . . . DT9–240–4/5
for 23 x 70 mm round shank . . . . . . . DT9–240–4/5
for 25 x 75 mm round shank . . . . . . . DT9–240–1/3/6
for 26 x 70 mm round shank . . . . . . . DT9–240–1/3/6
Fronthead Assembly
for 7/8" x 3 1/4" (22 x 82 mm)
hex shank . . . . . . . . . . . . . . . . . . . . . . DT9–A240–1/3/6
for 1" x 4 1/4" (25 x 108 mm)
hex shank . . . . . . . . . . . . . . . . . . . . . . DT9–A340–2
46
Fronthead (bare)
for 7/8" x 3 1/4 (22 x 82 mm)
hex shank . . . . . . . . . . . . . . . . . . . . . . DT9–240–1/3/6
for 1" x 4 1/4" (25 x 108 mm)
hex shank . . . . . . . . . . . . . . . . . . . . . . DT9–340–2
* Not illustrated.
To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one (pair or set) of each part indicated
by a bullet ( ) for every four tools in service.
PART NUMBER FOR ORDERING
49
Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
Plunger Spring . . . . . . . . . . . . . . . . . . . . .
51
Plunger . . . . . . . . . . . . . . . . . . . . . . . . . . .
T Handle Assembly . . . . . . . . . . . . . . . . . . . . DT13–A135
53
T Handle . . . . . . . . . . . . . . . . . . . . . . . . .
54
Throttle Lever . . . . . . . . . . . . . . . . . . . . .
56
Roll Pin (2) . . . . . . . . . . . . . . . . . . . . . . .
57
Valve Plunger . . . . . . . . . . . . . . . . . . . . . .
58
Throttle Spring . . . . . . . . . . . . . . . . . . . . .
59
Swivel Connector . . . . . . . . . . . . . . . . . . .
60
O–ring Connector . . . . . . . . . . . . . . . . . .
61
Connection Cap . . . . . . . . . . . . . . . . . . . .
62
O–ring Cap . . . . . . . . . . . . . . . . . . . . . . . .
Outside Trigger Assembly . . . . . . . . . . . . . . . DT10–A1
63
Outside Trigger . . . . . . . . . . . . . . . . . . . .
64
Intermediate Lever . . . . . . . . . . . . . . . . . .
65
Outside Trigger Handle . . . . . . . . . . . . . .
66
Pin (2) (Intermediate Lever Pin,
Trigger Pin) . . . . . . . . . . . . . . . . . . . . . . .
67
Hitchcutter Retainer
7/8" x 3 1/4"
(22 x 82 mm) hex shank . . . . . . .
22 x 70 mm round shank . . . . . . .
23 x 70 mm round shank . . . . . . .
25 x 75 mm round shank . . . . . . .
26 x 70 mm round shank . . . . . . .
*
Hitchcutter Retainer Guard . . . . . . . . . . . . . . DT10–23
*
Swivel Inlet Connector . . . . . . . . . . . . . . . . . DT9–A167
*
Air Feed Tube Assembly (for models
with power Regulator) . . . . . . . . . . . . . . . . . . DT10–A166
DT9–241
DT10–567
DT10–245
DT13–135
DT13–66
DT13–120
DT13–65
50250539
51609295
95086161
51361798
95086112
DT10–78
DT10–79
DT10–1
DT10–120
DT9–273–1/3
DT9–273–4/5
DT9–273–4/5
DT9–273–1/3
DT9–273–6

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Irgopic dt 10 serie

Tabla de contenido