Protecting The Environment; Service Information - Black+Decker BWL900 Manual De Instrucciones

ii. In case of eye contact, rinse abundantly with clean
water for at least 10 minutes. Consult a physician.
Fire hazard! Avoid short-circuiting the contacts of
a detached battery. Do not incinerate the battery.
Chargers
1. Use the charger provided with the tool only to charge
the battery
2. Never attempt to charge non-rechargeable batteries.
3. Have defective cords replaced immediately.
4. Do not expose to water.
5. Do not open the charger.
6. Do not probe the charger.
7. The charger is intended for indoor use only.
Safety warning for work-Light
This is not a toy; children should not permit to use it. This
is a DIY product, all electronic parts fixed already, any
intention of opening work-light or changing work-light
design is prohibitive unless a professional electrician.
Do not attempt to replace or change or the diode lights!
If the protective glass is cracked or broken, it must be
replaced before the work light can be used again.
OPERATION
Charging the work light
1. Open the protective cap and push the plug into
charger socket (7).
2. Plug the adapter into a suitable outlet. Do not use an
extension cord. The power light will be light and turn
red to show the battery is charging.
3. When the battery of work light is loaded, the power
light changed from red light to green light until the
charger disconnect from the mains.
Note: Put the protective cap into charger socket before
unplug which to avoid water enter.
Adjusting the light direction
The work light head can be tilted vertically up to 30° down
or 90° up.
To adjust the Light Direction, loosen the side locking
knob (4-Fig. A). Adjust the work light head to the desired
position, and retighten the knob.
On/off switch
The work light is equipped with an ON/OFF switch (8-Fig. A)
located on the left side of the work light.
With ON/OFF switch: 1st ON: 100% brightness; 2nd ON:
50% brightness; 3rd ON: 25% brightness; 4th ON: SOS
flashing.
Warning! Do not stare directly at the light beam. Never
aim the beam at any person or an object other than the
work piece.
Do not deliberately aim the beam at personnel and ensure
that it is not directed towards the eye of a person for longer
than 0.25s.
MAINTENANCE
Your work light requires very little care and maintenance.
Simply clean the lens regularly with a non-abrasive
cleaner, we recommend the work light to be completely
discharged every one month and fully recharged again
.Only store with a fully charged battery and top-up the
charge from time to time if stored for a long time. Store in
a dry and frost-free place, the ambient temperature should
not exceed 40°C.
Warning! Always make sure the work light is off and
complete cool before attempting to clean it.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are
available from your local dealer or authorized service center.
Warning! The use of any accessory not recommended
for use with this tool could be hazardous.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be
disposed of with normal household waste. Should
you find one day that your BLACK+DECKER
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials. Local regulations may
provide for separate collection of electrical products
from the household, at municipal waste sites or
by the retailer when you purchase a new product.

SERVICE INFORMATION

BLACK+DECKER offers a full network of company-owned
and authorized service locations. All BLACK+DECKER
Service Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool service.
For more information about our authorized service centers
ENGLISH • 13