Use And Maintenance - MO-EL MO-PLIK 398 Manual De Uso Y Mantenimiento

USE AND MAINTENANCE

IMPORTANT SAFETY INSTRUCTIONS
Before any installation, use and maintenance operation, read the
safety instructions contained in the manual carefully.
This electrical device is manufactured in accordance to HACCP
food-processing directive (CE 93/43-96/3-DL 155/97). It has
been manufactured in accordance with the CEE Low-Tension
Directive 73/23 and successive amendment no. 93/68 and the
CEE Electromagnetic Compatibility Directive no. 89/336.
This appliance is intended exclusively for the use for which it
was created, that is the destruction of the flying insects, and the
producer would not be considered responsible for any damage
caused by it's improper use.
THE COMPANY DECLINES ANY RESPONSIBILITY FOR THE
FOLLOWING:
Accidents to persons, to things and to the environment as well
as malfunctions of the appliance caused by:
A lack of a proper maintenance of the machine
o
The alteration of the configuration or original structure of the
o
device
An operation or usage unrelated to the terms described in
o
the content of this manual of instructions.
GENERAL WARNINGS
Before use remove all packing materials from the appliance.
o
In order to avoid danger of suffocation, keep the packing ma-
o
terials away from babies and children.
Do not use if unit is damaged.
o
Use the appliance exclusively for the use for which it was
o
created.
Do not allow that children or handicapped operate the ap-
o
pliance.
Before inserting the plug make sure that the voltage is the
o
same as indicated on the device.
Do not plug in the appliance in presence of inflammable ma-
o
terials, gas or liquids.
Keep cord away from heat.
o
Always disconnect the
o
maintenance operation.
Do not spread any inflammable liquid, gas or material on the
o
appliance.
In case of malfunction, verify the correct operation of the e-
o
lectric installation: whether it was right but the appliance still
shows problems a qualified technical service will be able to
do any repairing.
For a best appliance's performance use only spare parts
o
supply by the manufacturer.
FUNCTIONING
The special UV-A lamp is set to attract all flying insects to the
appliance.
When insects approach they remain stuck on the glued paper
supplied as a spare part.
This appliance allows monitoring and capturing flying insect
within the environment nearby.
INSTALLATION
This device is installed by fixing the three supplied screw an-
chors to the wall. A branch point or light socket must be nearby;
do not use extension cables or cables with plugs. The electrical
connection must be carried out with the conductors protected by
a Ø 16 mm sheath.
A bipolar thermal-magnetic differential switch with at least 3 mm
contact opening distance must be mounted upstream along the
supply line. Before making the connections make sure that the
switch contacts are open.
Place the device at a height of around 2 metres, in the darkest
part of the room, far away from any windows. This will allow the
device to eliminate the insects inside the house and will avoid
attracting those which are outside. The wall must not present
appliance before doing
EN
any obstructions which could make it difficult to remove the
sticking paper or clean the device. Make sure that the wall
where the device is to be mounted is solid and that no electric
cables pass through it. Using a drill with a 5 mm bit, make three
holes in the wall and insert the screw anchors supplied in the
holes.
Fix the device to the wall placing the two screws in the holes in
the upper part as shown below (fig. 1). Open the device cover
and using a pair of scissors cut just enough off the cable pas-
sage to slide in the conductor protection sheath. Make the elec-
trical connections and close the cover. At this point, fix the third
screw into the screw anchor in the central part of the device so
that it also locks the cover. Screw the bulb into the bulb holder,
as shown in the illustration (fig. 2). Then place the sticking paper
into position; remove the protective film from the paper, and
place it centrally on the cover and slide it into the fixing grippers
as shown in fig. 3.
Finally, mount the cover with the sticking paper into the central
body of the device taking care to slide the upper rim of the cover
into the upper lip of the base, as shown in fig. 4.
MAINTENANCE
Before carrying out any maintenance or cleaning operation
o
on the machine make sure that the contacts on the bipolar
switch are open.
In case of malfunction, take the device to the nearest techni-
o
cal service centre or sales outlet.
The sticking paper must be replaced at least once a month
o
or more often if used in particularly dirty places or where the-
re are lots of insects.
The device should be cleaned each time the paper is repla-
o
ced. Use a suitable detergent for cleaning, such as those u-
sed for environments where food is produced.
Once the cleaning operation is completed, replace the used
o
sticking paper with a new one. All maintenance operations
must be carried out on the floor.
Replace the sticking paper regularly, at least once a month.
o
Clean the lamp and the whole device regularly.
o
To ensure the best operation of the device, replace the bulb
o
once a year.
any If the sticking paper gets stuck to the lamp, clean it with a
o
soft cloth soaked in non-corrosive detergent, taking care not
to scratch the lamp.
The rejected or used sticking papers must be disposed off in
o
conformity with the regulations in force in the place the devi-
ce is installed.
TECHNICAL ASSISTANCE
For any queries regarding this device, please contact your sup-
plier. In case of breakdown or malfunction, switch the device off
and take it or send it to the nearest technical service centre.
Only authorised technical service centres which use original
spare parts can carry out repairs.
4