Halemeier S-Mitter MultiWhite2 Manual De Instrucciones página 4

S-Mitter MultiWhite²
Typ: HA-MW2-SMS
Typ: HA-MW2-E
Instructions for controlling an S-Mitter by several transmitters:
As each individual transmitter changes command on the push of a button, it is possible that an additional transmitter may have to be activated twice.
This may be the case if the lighting was switched off with transmitter A for example and it was then switched back on with transmitter B.
In this case transmitter A would send an „On" command when the corresponding button was pressed. This would not, however, lead to a switching function as it
had already been shifted to this switching status by transmitter B in the meantime.
Instructions for control of several MultiWhite² receivers by one transmitter:
The transmitter gradually sends signals concerning brightness and colour temperature control to the receivers. If the receivers are some distance away from one
another, it is possible that the signal may not be transferred to all receivers. This is balanced out with the next signal change on the transmitter. The system is
synchronised once again.
Connection of the S-Mitter MultiWhite²
Establish connection of the power supply via the connections on the MultiWhite² receiver. Voltage and output of the load must match the selected power supply/
electronic ballast. The limit values of the S-Mitter basic must be adhered to. 12VDC max. 36W.
Programming of S-Mitter MultiWhite²
The distance between wireless transmitter and MultiWhite² receiver should not exceed 0.5 m here. 5 different transmitters can be taught into an S-Mitter basic
MultiWhite². The wireless transmitter can be taught into an unlimited number of spread over max. 4 groups wireless transmitters.
Procedure - teaching in:
1. A button for programming and an LED for display are located on the MultiWhite² receiver.
2. Press the programming button on the S-Mitter MultiWhite² down briefly for approx. 1 second until the LED lights up
permanently.
3. Then press the channel button a-d on (+) or (-) on the hand-held transmitter down straight away for
two times in order to send a message. The LED goes out briefly. A maximum of 5 transmitters can be taught in.
4. The programming process is ended automatically after approx. 10 seconds or it can be ended immediately by pressing the
programming button on the S-Mitter again.
How to clear a learned transmitter - delete entire transmitter memory
1. Keep the programming button on the MultiWhite² receiver pressed down. The LED will begin to flash.
2. Continue to hold programming button down until the LED stops flashing.
3. After releasing the button, all transmitters will be deleted.
Wireless transmission
A non-exclusive transmission path which is available is used for wireless transmission so errors cannot be ruled out. The wireless transmission is not suitable for
safety applications (emergency stop, emergency call). The wireless system is intended for use in the living area. The transmission range of a wireless transmitter is
up to 30m in a free field.
Hazards and disposal instructions
Ensure that the load which is plugged in is in a secure state so that the switching on of the load does not cause any danger. The appliance is only intended for the
switching and dimming of lighting and no other terminal devices may be connected to the system. Observe the maximum permissible load of the connected load /
electronic ballast and MultiWhite² receiver (see technical data).
Keep batteries out of reach of children.
If batteries are swallowed, call a physician immediately. Do not reverse polarity of the batteries and observe the [+] and [-] marks on the battery and the device. The
device is supplied with standard batteries which must not be charged. Charging these batteries may result in material damage and personal injury due to explo-
ding or leaking batteries. Observe all safety instructions printed on the battery. Never open the battery or throw the battery or device into a fire. Observe the local
regulations for disposal.
4
cM M 3 q
en LED ballast - This device should be accessible for maintenance.
Halemeier GmbH - Lange Straße 51 - D 49326 Melle Neuenkirchen
m
Installation below mirrors,
metal surfaces and foil must be
avoided.
/
25.394.06 19.12.2017