GenTran 15116V Instrucciones De Instalación Y Funcionamiento

Installation and Operating Instructions
GENERATOR SAFETY TRANSFER SWITCH MODELS 15116V, 30116V, 20216V, 30216V, 30310V
Model 15116V
CAUTION: No appliance should have an amperage rating that exceeds the individual breaker rating in the transfer switch. The total
amperage of all circuits can exceed the generator rating, but not all circuits will be able to be used concurrently. Do not connect any
appliance that is rated at more than 15 amps (Model 15116V) or 20 amps (Models 30116V, 20216V, 30216V, 30310V). Gen/Tran is
not responsible for accidents or property damage due to incorrect or inappropriate installation.
Model:
# Circuits Provided
Max GEN Watts
Max GEN Amps
[Can be hardwired
for 120/240 volts]
Voltage
# of 2-pole circuits
NEMA Type Enclosure
NEMA Configuration of
Male Inlet
Phase
Compatible
Power Inlet Box
Power Cord Wire Gauge 12 gauge, 3 wire
Tools Needed for Installation:
• Power Drill
• Wire Stripper and cutter
• Screw drivers
• Tape measure
• 4 wall anchors and screws
Thank you for purchasing a Gen/Tran
safely connect a portable generator to the load center in your home or business
(single phase only) for standby power applications. Product features include:
Pre wired for fast, easy connection to the load center
•
3-position switches for transferring circuits from utility to generator power
•
Dual wattmeters are provided to help you monitor and balance the loads on your
•
generator, prolonging generator life
• Power Inlet for quick cord connection to your generator
• Aluminum enclosure won't rust (for indoor use only)
• No feeder breaker needed in main load center/electrical panel
Warning: Gen/Tran transfer switches should be installed by a professional electrician familiar
with electrical wiring and codes, and experienced in working with generators. Gen/Tran
accepts no responsibility for accidents, damages or personal injury caused by incorrect
installation. These transfer switches are intended for surface mounting INDOORS only.
Gen/Tran transfer switches are made from UL listed or recognized components, and meet the
criteria of National Electrical code Article 702.6 for Optional Standby Systems.
15116V 30116V
4 – 15 amps
6 – 15 amps
2 – 20 amps
1875 3750
15 Amps @ 120
30 Amps @ 120 volts
volts
[Can be hardwired for
120/240 volts]
120 Volts 120 Volts
1
[Only if hardwired and
0 used with a generator
that produces 120/240
volts]
1 – Indoor Only 1 – Indoor Only
5-15 L5-30
1 1
NA 53002 or 530V
10 gauge, 3-wire
®
Manual Transfer Switch designed to
20216V 30216V
4 – 15 amps 4 – 15 amps
2 – 20 amps 2 – 20 amps
5000 7500
20 Amps @ 120/240 30 Amps @ 120/240
volts volts
120/240 Volts 120/240 Volts
1
1 – Indoor Only 1 – Indoor Only
L14-20 L14-30
1
14202 or 1420V 14302 or 1430V
12 gauge, 4-wire 10 gauge, 4-wire
• 6 or 10 wire connectors (yellow size)
• Other supplies needed if hardwiring to a Power Inlet
Box include Romex, ½" connector, and wire
connectors
30310V
6 – 15 amps
4 – 20 amps
7500
30 Amps @ 120/240
volts
120/240 Volts
1 5
1 – Indoor Only
L14-30
1 1
14302 or 1430V
10 gauge, 4-wire