Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation Instructions for 70-8114
Installation:
1. Connect the Red wire to 12-volt accessory power.
2. Connect the Black wire to chassis ground (by itself).
3. Connect the 3.5mm jack to the steering wheel control input, in the aftermarket radio.
4. Connect the White RCA jack to the left audio AUX IN of the aftermarket radio
(if equipped).
5. Connect the Red RCA to the right audio AUX IN of the aftermarket radio (if equipped).
Note:
• Audio devices connected through the 3.5mm jack will be controlled from the audio
device, not the aftermarket radio.
• Please refer to the ASWC-1 programming instructions for programming of the ASWC-1.
K
P
NOWLEDGE IS
OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
1-800-221-0932
REV. 10/13/2014
© COPYRIGHT 2004-2014 METRA ELECTRONICS CORPORATION
Metra recommends MECP
certified technicians
metraonline.com
Installation Instructions for 70-8114
70-8114
Toyota/Lexus/Scion ASWC-1 harness
APPLICATIONS
LEXUS
TOYOTA
4-Runner*
ES-Series
2002-2006
4-Runner
GX-Series
2003-2009
Avalon
RX-Series
2004-2009
Camry
Corolla*
SCION
Corolla
iQ
2012-up
FJ Cruiser*
tC
2005-2013
FJ Cruiser
xA
2004-2006
Highlander*
xB
2004-up
Highlander
xD
2008-up
Matrix*
* These vehicles use either a 20-Pin or 28-pin connector for the steering wheel control
harness. If your vehicle uses a 28-pin connector, please use the AX-TOY28SWC instead.
Caution: Metra recommends disconnecting the negative battery terminal before beginning
any installation. All accessories, switches, and especially air bag indicator lights must be
plugged in before reconnecting the battery or cycling the ignition.
Note: Refer also to the instructions included with the aftermarket radio.
Connections to be made
When installing an aftermarket radio, the 70-8114 will allow the user to retain their factory
installed steering wheel controls without having to splice into the factory wiring (ASWC-1 required
and sold separately). In addition, we include RCA's to allow the user to retain their factory installed
3.5mm AUX IN jack (aftermarket radio must have a audio AUX IN).
Continued on back
1-800-221-0932
REV. 10/13/2014
© COPYRIGHT 2004-2014 METRA ELECTRONICS CORPORATION
Matrix
2009-2012
2012-2013
Prius
2004-2011
2003-2011
Rav-4
2005-2011
2005-2012
Sequoia*
2013-up
2005-2011
Sequoia
2003-2012
2011-2013
Sienna
2003-2014
2009-2010
Solara (Camry) 2004-2008
2013-up
Tacoma*
2012
2007-2012
Tacoma
2005-2011
2013
Tundra
2003-2013
2004-2012
2013
Venza
2009-2012
metraonline.com

Publicidad

loading

Resumen de contenidos para Metra 70-8114

  • Página 1 Note: Refer also to the instructions included with the aftermarket radio. Connections to be made When installing an aftermarket radio, the 70-8114 will allow the user to retain their factory installed steering wheel controls without having to splice into the factory wiring (ASWC-1 required and sold separately).
  • Página 2 Nota: Vuelva a montar el tablero en forma inversa al desmontaje. Conexiones que se deben hacer Al instalar un radio de posventa, el 70-8114 permitirá al usuario retener sus controles del volante EL CONOCIMIENTO ES PODER Mejore sus habilidades de instalación y instalados de fábrica sin tener que realizar un empalme al cableado de fábrica (requerido por el...