Fluidmaster 670 Guia De Inicio Rapido

11" (h) x 17" (w) ENGLISH SIDE
LOW RESOLUTION PDF
PART# 6-1095, Grev. 2, 03/14
DO NOT PRINT!
FLUIDMASTER
UNIVERSAL ARM
PREMIUM TANK LEVER SYSTEM
WARRANTY because it will not damage the components. DO NOT overtighten nuts or tank/bowl may crack.
Always use quality Fluidmaster parts when installing or repairing. Fluidmaster will not be responsible or liable for
use of non-Fluidmaster parts during installation or repair.
3
3A
4
INSTALL SHAFT & ARM
CONTINUED
4D
Push/Click
Push the shaft all the way in
until it clicks into the lever
mount.
7
ATTACH LEVER
7A
E
Hold base
of shaft
Push
Attach lever onto the end of
shaft. Align lever, hold base
of shaft and push lever into
place. (Lever and trim sold
separately)
670
®
NEEDED
REFERENCE
A) Lever mount
B) Locknut
C) Shaft
D) Latch
E) Arm
F) Adapter Sleeve
(optional)
Lever and trim
sold separately
WARNING
DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS CONTAINING
BLEACH OR CHLORINE. Use of such products will: (1) RESULT IN DAMAGE to tank
components and MAY CAUSE FLOODING and PROPERTY DAMAGE and (2) VOID
FLUIDMASTER WARRANTY.
Fluidmaster Flush 'n Sparkle Toilet Bowl Cleaning System is recommended for
those choosing to use in-tank bowl cleaners and WILL NOT VOID the FLUIDMASTER
INSTALL LEVER MOUNT
Bushing Sleeve
A
Tank hole
Push lever mount If you have a large tank hole and the lever mount
through tank hole from seems loose, attach optional adapter sleeve onto the
outside of tank until it lever mount and over the square bushing.
fits snugly against tank, (Sleeve loose in package)
but do not force it.
5
ADJUST ARM
Incorrect. Grooves not aligned.
5A 5B
E
Position the arm parallel to the front wall of
the tank, with end of arm directly above
flapper.
Side Mount Options:
End of lever pointed toward
Front Mount
rear of toilet
7B
Remove lever,
then trim
Front of toilet tank
- OR -
Angled Mount Lever pointing downward
If further adjustment is needed, remove lever and trim.
Then push end of shaft from outside tank until it disengages.
Adjust arm angle so the arm does not hit toilet tank lid.
Pull toward
Find desired angle before clicking the shaft back into place.
front
Front of toilet tank
TOOLS
Mini hack saw Slip-joint pliers
E
C
D
B
A
Trim
F
Lever (Optional) Adapter Sleeve
For large tank holes
View from inside of toilet tank
3B
B
A
Tighten locknut hand tight in a counter-clockwise direction.
Correct
D
Align grooves of the arm's pivot
point so the parts mate.
8
RECONNECT FLAPPER CHAIN
Further adjustment
Fully assembled cutaway front view of toilet tank
Flapper
A
Push
Attach flapper chain to one of the holes on arm, ensuring
there is 1/2" slack in chain.
When installing lever into a Mansfield toilet with a
210/211 tower flush valve, use Fluidmasters 5104
flapper chain.
6-1095_Grev2_PremLeverArm_Instr_032414
1 2
REMOVE OLD LEVER
Cutaway front view of toilet tank
2A
View from inside
of toilet tank
Remove tank lid. Unhook flapper chain
from tank lever. Loosen locknut by
turning counter-clockwise. (Pliers may
be needed) Slide nut off lever arm. Pull
lever through tank hole.
4
INSTALL SHAFT & ARM
4A 4B
B
D
IMPORTANT: Unlock latch.
Flip latch on arm up to
unlock. Arm should then
move freely.
6
ATTACH TRIM
Locked position shown.
D
Trim
Flip latch back to locked position. Carefully attach the trim by aligning
Ensure arm does not interfere with the teeth at the end of the lever
fill valve or other parts in the tank. mount with the slots on the trim.
A) IF TOILET TANK SPACE IS EXTREMELY TIGHT:
A1. Begin installing by placing the locknut loosely around
shaft and inserting shaft through the square tank mount
hole from the inside of tank.
A2. Slide lever mount through square hole from outside
E of tank over the shaft that was placed through tank hole in
step A1. Do not snap it in place yet.
A3. Hand-tighten locknut counter-clockwise.
Snap arm into place with end of arm angled slightly
A4.
Needs
chain lower than lever mount.
1/2"
slack
Proceed to step 5 (ADJUST ARM)
B) IF LEVER ARM IS TOO LONG:
Using notches in arm as a guide, trim end of lever arm if
it is still hitting toilet tank lid after adjusting. (Should not
be required for most installations)
30800 Rancho Viejo Road, San Juan Capistrano, CA 92675
www.Fluidmaster.com • 800-631-2011
Contact Fluidmaster for troubleshooting help or visit www.fluidmaster.com
M-F 5:30 am - 5:00 pm PST.
PREPARE NEW LEVER
2B
B
C A
Remove lever arm from Remove locknut by turning
package. Pull lever mount
it clockwise.
off shaft as shown above.
Cutaway front view of toilet tank
Front view of toilet tank
4C
E
C
Flapper
A
chain
From inside of tank, slide Position arm to reach
shaft through lever mount flapper chain length. End
most of the way but do not of arm should be angled
click it into place yet. slightly lower than lever
mount.
Align & Push into place
Push
Teeth
Push into place. (Trim sold separately
with Premium Lever)
A1 A2
A3 A4
View from inside of toilet tank
B