Safety Rules - Ryobi EHG2000 Manual Del Usuario

SAFETY RULES

Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
■ Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
■ Do not operate
atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
■ Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
■ Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adaptor
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
■ Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
■ Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
■ Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
■ When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
■ If operating power tools in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
■ Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
■ Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
■ Do not use the power tool if the switch does not turn
it on and off. Any power tool that can not be controlled
with the switch is dangerous and must be repaired.
■ Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
WARNING
power tools in explosive
users.
■ Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from intended could result in a
hazardous situation.
■ Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
■ This product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
product by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the product.
Read these safety instructions. Before using the
heat gun, please read the manual carefully, especially
the safety instructions. Keep this manual for future
reference.
■ This heat gun may start a fire if appropriate precautions
are not taken.
■ The heat from the heat gun may reach combustible
materials which you may not be able to see.
■ Do not leave the heat gun unattended while it is
operating.
■ Keep the heat gun away from rain or water to avoid
risks of fire or electric shock.
■ Store under cover in a dry place.
■ The nozzle gets extremely hot: wear gloves and eye
protection.
■ For your own safety, please read this manual carefully.
■ When servicing, always use manufacturer's original
parts to replace worn or damaged parts.
■ Do not direct the hot airflow towards people or animals.
■ Never use the heat gun near flammable materials or in
the presence of flammable gases.
■ Never reduce the hot airflow by blocking or covering
the nozzle.
■ Be careful not to touch the nozzle as it becomes
extremely hot.
■ Ensure that the nozzle does not come into contact with
materials during or just after operation.
■ Always wear eye protection when stripping paint
overhead.
■ When using the heat gun, do not wear loose clothing
or jewellery, wear non-slip footwear and a hair net to
English
WARNING
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR
1