Olympia NC 520 Manual De Instrucciones página 12

Batch (NC 520, 540, 560, 570)
This function causes counting to stop when the preset
quantity of bank notes has been counted. If the counted
batch of bank notes is removed from output tray, the
display [5]/[15] skips back to
counted.
The quantity of bank notes can be set to any number
1 999
between and . The preset quantity appears in the
display [4]/[14].
If the infeed tray becomes empty before the quantity set
is reached, the display [5]/[15] flashes. If more bank
notes are then inserted in the infeed tray, the process is
resumed.
Æ BATCH Ê The Batch function is activated.
Each time the button is pressed, the quantity set is in­
10
creased in steps of ,
BATCH button one more to deactivate the function.
Æ + 1x ÊThe preset quantity is increased by 1.
Æ + Ê The preset quantity is increased automat­
ically.
Æ CLEAR Ê The preset quantity is reset to
Currency (NC 560, 570)
This function enables bank notes with a different value
but of the same currency to be counted in one opera­
tion. In this case, the machine establishes the total
value of all the bank notes and the quantity of bank
notes according to each specific value.
Æ CUR until the required currency (
SEH
) appears in the display [16].
Æ MODE until VALUE appears in the display [17].
When the counting process has finished:
Æ REP/PRINT Ê The value of the bank notes [16] and
quantity [17] of the corresponding bank note according to
its value.
Æ REP/PRINT Ê The next bank note value appears.
4 seconds after the last button was pressed, the total value
reappears in the display [15].
Æ REP/PRINT 3 sec.
vidual bank notes and the total value are printed out on a
printer.
To be able to print, a printer must be connected at
the RS-232 port.
Sorting (NC 560, 570)
With this function, the first bank note is used as a refer­
ence for those following. If the machine detects a bank
note which deviates from it, the machine stops. The
display [4]/[14] shows CF3
be sorted out.
12
X 0
and the next batch is
20 25 50 100
, , and . Press the
Eur tL
,
Ê The quantities of the indi­
. The deviating bank note can
Only those bank notes are counted which match the
first note. The total value of bank notes counted is also
established.
Æ CUR until the required currency (
SEH
) appears in the display [16].
Æ MODE until SORT appears in the display [17].
When the counting process has finished:
Æ REP/PRINT
value are printed out on a printer.
To be able to print, a printer must be connected at
the RS-232 port.
Validation functions
The best results are achieved after a warm-up
phase of 3 minutes.
Bright ambient light can affect the sensor and falsify
results.
The range of validation functions is dependent on the
machine concerned.
Setting the Function and Sensitivity (NC 560
X 0
.
and NC 570)
Æ MODE 3 sec.
sensitivity is activated. The sensor is indicated by flashing
in the display [17] and [14].
Æ + Ê The sensitivity is altered and indicated in the
display [17] by bars following the sensor. If there is no bar
displayed following the sensor, the sensor is switched off.
Æ MODE Ê Move to the next sensor.
GbP
, or
After all the sensors have been set:
Æ MODE Ê Exit from the setting function.
Connected (NC 520, 540, 560, 570)
This function is triggered when the width of the bank
note is exceeded by 1/3. The display [4]/[14] then
shows EC .
This function is always active.
G
Eur
Ê The quantity and total
3 sec.
Ê The function to set the sensor
tL GbP
, , or