Lavor EDS-M 15000 Manual De Instrucciones página 29

Bomba de drenaje
Ocultar thumbs Ver también para EDS-M 15000:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
4) Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation.
if damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
h) If the supply cord is damaged, it must be
replaced by a special cord or assembly
available from the manufacturer or its service
agent.
5) Service
a) have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
6) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and
fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
if contact accidentally occurs, flush with
water. if liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
When using the pump, always observe the
following safety instructions.
Before use check the pump for damage.
n
Should the pump be damaged, it must not be
used.
Only connect the pump to an electric group
n
which is protected with an earth leakage
switch (30 mA).
Do not use the pump in swimming pools or other
n
places where persons could find themselves in
the vicinity of the pump in the water.
Do not use the pump in fish ponds or
n
fountains.
Never use the pump if no outlet pipe of min.
n
20 cm has been fitted.
If the pump is used for pumping drinking water,
n
the installation must be rinsed thoroughly.
Never let the pump run dry.
n
Never carry the pump by the mains cable or
n
float switch, but only by the handle.
Always remove the mains plug from the wall
n
socket before moving or servicing the pump.
If the mains cable is damaged, it has to be
n
replaced by the manufacturer, its after­sales
service or a similarly qualified person, in order
to avoid a danger.
gB
29

Publicidad

Tabla de contenido
loading

Tabla de contenido