Black+Decker HP120K Manual De Instrucciones página 16

16 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c. When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a fire.
d. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
7. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
8. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
FEATURES (Fig. A)
1. Variable speed switch
2. Forward/reverse slider
3. Mode selector / torque adjustment collar
4. Chuck
5. Two-gear selector
6. Battery charge indicator
7. Bit holder
9. Battery
10. Battery release button
11. Charger
ADDITIONAL SAFETY INSTRUCTIONS FOR
BATTERIES AND CHARGERS
BATTERIES
f Never attempt to open for any reason.
f Do not expose to water.
f Do not store in locations where the temperature may
exceed 40°C.
f Charge only at ambient temperatures between 4°C
and 40°C. Charge only using the charger provided
with the tool (see technical data).
f Before charging, make sure that the battery is dry and
clean.
f Use only the correct type of battery for the tool (see
technical data).
f When disposing of batteries, follow the instructions
given in the section "Protectingthe environment".
f Under extreme conditions, battery leakage may
occur. When you notice liquid on the battery,
proceed as follows:
f Carefully wipe the liquid off using a cloth. Avoid
skin contact.
f In case of skin or eye contact, follow the instructions
below.
Warning! The battery fluid, a 25-30% solution of
potassium hydroxide, can be harmful. In case of skin
contact, immediately rinse with water. Neutralize with a
mild acid such as lemon juice or vinegar. In case of eye
contact, rinse abundantly with clean water for at least 10
minutes. Consult a physician.
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
Construction
Earthing
Terminal
Safety Alert
Symbol
Revolutions
or Recipro-
cation per
minute