Working Instructions; Maintenance And Care; Declaration Of Conformity - Felisatti AF115/900 Instrucciones De Servicio

To switch off, do the same in reverse.
Constant electronic performance (mod. AF125/1100VES)
The built-in module permits:
- Soft start.
- The maintenance of a practically constant rated speed
up to rated power.
- Speed control.

WORKING INSTRUCTIONS

For cutting or deburring, the part to be worked on must be
secured, unless it is heavy enough to remain in a stable
position by itself.
For optimum performance and results when deburring,
it is advisable that the surface and the disc form an angle
of approximately 0º-0º. Guide the tool by pressing
lightly forwards and backwards. This prevents the part
from overheating or changing colour and the formation of
striations. (Fig. )
WARNING! Never use a cutting disc for deburring.
When cutting, do not exert pressure on the disc. Do not tilt
the machine. The disc should not tilt or oscillate. Work with
a steady speed, appropriate for the type of material. When
cutting, bear in mind the direction of the work. Guide the
machine against the direction of the cutting tool, never in the
opposite direction; otherwise there is a risk of the machine
veering off the cutting line uncontrollably. When cutting
profiles or rectangular section tubes, we recommend starting
the cut on the shortest side.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.

MAINTENANCE AND CARE

WARNING! Always unplug the machine before carrying out
work on it.
- Inspect the tool: Using a worn deburring or cutting tool
will diminish the efficiency of the work and could damage the
motor.
- Inspect the mounting screws: Regularly inspect all the
mounting screws and ensure they are firmly tight-ened.
Should any screw be loose, tighten it immedi-ately. Failure to
do so could put you at serious risk.
- Motor maintenance: Always take the greatest care over
this and make sure that the motor winding is not damaged
and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is not,
take it to an Official Service Centre to have it replaced.
- Brush replacement: The brushes should be replaced
after 10 00 hours use or when they are less than 10 mm
long. Have this done by an Official Service Centre. We
recommend that at every second change of brushes, you
take the machine to one of our Official Service Centres for
general cleaning and oiling.
- Use only Felisatti accessories and spares. Parts the
changing of which is not covered in this instruction man-ual,
should be replaced in a Felisatti Official Service Cen-tre (See
Warranty/Official Service Centre address leaflet).
6
Do not dispose of electric tools
in the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances
and its translation into national law, used electric
tools must be collected separately and recycled in
an ecologically desirable way.
DECLARATION OF
CONFORMITY
We hereby declare, under our sole
responsibility, that the FELISATTI
brand products described in this manual
comply with the following standards
or stan-dard documents: EN60745-
1:2009,EN60745-2-3:2007,EN55014-
1 : 2 0 0 6 + A 1 , E N 5 5 0 1 4 -
2 : 1 9 9 7 + A 1 + A 2 , E N 6 1 0 0 0 - 3 -
2:2006+A1+A2
3-3:2008 in accordance with EU
Directives
EC,2004/108/EC,2002/96/EC.
We reserve the right to make technical changes 06/2011
and EN61000-
2006/42/EC,2006/95/
Francisco Ruis
Technical manager.