Publicidad
Idiomas disponibles
Idiomas disponibles
NEXA AUDIO AND VIDEO DOOR ENTRY SYSTEM - NFC ACCESS CONTROL MODULE
SAFETY PRECAUTIONS
( )
*
- Always disconnect the power supply
before installing or making modifications to the devices.
The fitting and handling of these devices must be carried out by authorised personnel.
-
The wiring must run at least 40cm. away from any other wiring.
-
-
On the power supply unit:
Do not overtighten the screws on the connector.
w
Install the power supply unit in a dry protected location free from the risk of dripping or splashing
w
water.
wAvoid locations that are humid, dusty or near heat sources.
wEnsure that the air vents are free from obstruction so that air can circulate freely.
wTo avoid damage, the power supply unit must be firmly secured in place.
wTo prevent electric shock, do not remove the cover or handle the wires connected to the
terminals.
CHARACTERISTICS
( )
*
-
NFC access control module (Golmar proximity cards).
-
Can be combined with 'Nexa Modular' and 'Inox Modular' door panels.
-
Basic configuration using the SW1 configuration DIP switch or Master card.
-
Advanced configuration and management of the NFC access control. Mobile with NFC and AC
Manager app required (Android only), see the TAC Manager manual (code 50124945).
-
Enables management of the residents' card/key tag to activate the lock release of the NFC
access control via mobile. Mobile with NFC and OpenGo app required (Android only), see the
TOPENGO manual (code 50124946).
-Status LED and tones.
DESCRIPTION OF THE MODULE
( )
*
a.
Front.
b.
Proximity card reader.
c.
Status LED (two-colour red/green).
Description of the monitor connector:
:
Power input.
~ ~
NA1
:
Normally open output relay 1.
C1
Common relay 1.
NC1
:
Normally closed output relay 1.
-
: Negative.
PL1
:
Input for exterior button relay 1.
( )
For more information, see the T4503/NFC user manual (code 50122088).
*
https://doc.golmar.es/search/manual/50122088
a
d
b
e
c
f
g
d.
Back.
e.
Monitor connector.
f.
SW1 programming DIP switch.
g.
P1 programming button.
2
NEXA AUDIO AND VIDEO DOOR ENTRY SYSTEM - NFC ACCESS CONTROL MODULE
DESCRIPTION OF THE DOOR PANEL
( )
*
Exploded view of the parts of the panel.
Embedding boxes
MOUNTING CONFIGURATIONS
( )
*
NFC access control combined with Nexa button panels:
This equips the door panel with NFC access control, allowing users to make calls to apartments
using the call buttons. The site can also be accessed by waving a residents' card/key tag
(Golmar) over the EL4503/NFC module.
Add residents' cards/key tags: set DIP switch 3 to ON, the LED on the
front will blink (red). Then wave the new residents' NFC/US cards /
TAGNFC/US key tags (Golmar) that you wish to add over the
EL4503/NFC proximity reader one by one, the module will emit 2 tones
and the LED will light up (green) for one second every time a residents' proximity
card/key tag is memorised or the LED will blink rapidly (red) if the card/key tag has
already been memorised. Up to 2,000 cards/key tags can be memorised. To exit
'Add residents' cards/key tags' mode, set DIP switch 3 to OFF, the LED on the front
(red) will turn off.
Remove all residents' cards/key tags: set DIP switches 1 and 3 to ON,
the LED on the front will blink (red). Then press the P1 programming
button for 5 seconds, the LED will blink rapidly (red); after 5 seconds,
the LED will light up (green) for 1 second and the module will emit 2 short
tones indicating that the process has been carried out successfully.
To exit 'Remove all residents' cards/key tags' mode, set DIP switches 1 and 3 to
OFF, the LED on the front (red) will turn off.
Programming relay 1 activation time by access with card/key tag: set
DIP switch 5 to ON, the LED on the front will blink (red). Press and hold
down the P1 button, the red LED will turn off and the green LED will
blink; each blink will increase the minimum activation time of 3 seconds
already set at the factory by 1 second. Once the desired activation time
has been selected, stop pressing the P1 button, the module will then emit 2 short
tones and the LED will light up (green) for 1 second confirming the new activation
time.
If you wish to reset the default time of 3 seconds, press the P1 button.
To exit 'Relay 1 activation time with card/key tag' mode, set DIP switch 5 to OFF, the
LED on the front (red) will turn off.
( )
For more information, see the T4503/NFC user manual (code 50122088).
*
https://doc.golmar.es/search/manual/50122088
Electronic
Frame modules
modules
3
Aluminium panel
SW1
P1
SW1
P1
SW1
P1
Continued overleaf.
Publicidad
