Intended Use; Technical Data - Chamberlain 5002EX Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 7
Disconnect power supply to the door drive before installing the receiver.

INTENDED USE:

Only for garage door and yard gate openers installed and operated
according to the CE (Europe) quality standard. The connection of the addi-
tional receiver should be made in such a way that the safety functions and
related devices described in the manual of the drive are not bypassed,
disabled or impaired.
Functional principle:
The 2-channel universal receiver can control up to 2 different drives. These
are connected to either CH1 or CH2. The relay is held closed so long as a
signal of a programmed handheld transmitter is received.
If a button on the handheld transmitter is already used for another drive,
this button must NOT be additionally programmed for the universal receiver.
The buttons that activate CH1 and CH2 on the transmitter are pre-
programmed at the factory (Fig.5).
INSTALLATION
Open the receiver with a suitable screwdriver. Mount the receiver with the
supplied mounting screws and dowels (Fig. 1). The receiver should be
mounted as far forward as possible, preferably 2 feet or higher above the
ground. Choose a place where there is sufficient space for opening the
cover and the antenna (as far as possible from metal structures).
Use only in dry areas.
Voltage supply:
A: Transformer 12VAC/DC, 15V AC/DC, 24VAC/ DC. Minimum 200mA
(Accessories: G23015UNI)
B: From the drive that already supplies the corresponding voltages via a
special output.
Connector description:
1. 12 V - 24 V and GND are the connecting terminals on the board (Fig. 2).
Connect the transformer cable to the terminals.
Then tighten the terminals firmly.
2. Now connect the drive controller to the terminals of the universal receiv-
er. Thereby connect the cable of a button function (e.g. key switch) of the
drive to the connection terminals (channel 1) to (Fig. 3). Connect the
cable of the second wall switch (if you have to operate two doors) to the
connection terminals (channel 2) (Fig. 4). If there is no wall switch or key
switch, please check the manual of your drive.
3. Plug in the transformer and switch the power back on.
PROGRAMMING OF THE RECEIVER
Operate the door drive only when the door is in full view, there are no
obstructions and the drive is properly aligned. No one should be in
the swing area of the door. Do not allow children to use the buttons or
the remote control and also to play near the door.
1. Before programming, press the "CODE" button (LED begins to glow);
hold it down. After about 10 seconds, the LED goes out. The memory is
now erased.
Press "CODE" button (red) briefly and let go.
Press the desired button on the handheld transmitter
Ready Repeat the procedure for additional transmitters.
Delete (ALL transmitters)
Press "CODE" button (red) and hold for about 10 seconds.
(Red LED goes off)
Ready
Delete (individual handheld transmitter)
Press and hold "Clear Up" button. Also press and hold transmitter.
Release both buttons simultaneously after about 1-2 seconds.
Ready.
DIAGNOSIS
- LED on the receiver flashes: A transmitter (signal) is in range of the
receiver.
- The receiver has short range. Choose another place.
Straighten antenna and do not place on metal.
- The inverted channel (CH1-CH2) is activated. See "Delete a transmitter"
in this manual.
- The handheld transmitter cannot be programmed: Transmitter not
compatible (LED indicator on transmitter should be orange) or battery on
the transmitter is empty.
- The transmitter appears to have "forgotten" the code => Not possible.
Stop access to the receiver. Check battery on the transmitter.
Using another handheld transmitter, check the general function of the
receiver (power present). Wiring on the drive damaged. Drive is defective
or a safety device is disabled.
Notes:
Compatible with the transmitter types 54332XX and HE54332.
Up to 60 transmitters can be programmed on the receiver.

TECHNICAL DATA

Voltage IN:
Voltage OUT:
Relay switching load:
No. of channels:
Protection class:
Radio receiver:
Handheld transmitter:
Coding:
Suitable 2-channel handheld transmitter*:
5332E, 54332EML, HE54332, HE5433EX (*At the time of printing)
Accessories:
Universal G23015UNI transformer (not included)
12-24 Volt AC/DC
0 Volt (CH1, CH2)
Max. 36 Volt/1A
2 (CH1 & CH2)
IP22 (Do not use outdoors!).
433.92 MHz
max. 60x
Chamberlain special security rolling code

Publicidad

Tabla de contenido
loading

Tabla de contenido