Hoover H-GO 300 HYDRO PRO Manual De Usuario página 8

8
MOPPING FUNCTION
OPERATION
1. Remove the mopping cloth from the bottom part of the water tank. [Fig. 13]
 1RGP VJG YCVGT VCPM U TWDDGT ECR NN KV WR YKVJ YCVGT CPF ENQUG KV CICKP [Fig. 14]
Fig. 13
Add some cleaning agent if considered necessary.
3. Align the water tank with the RQDQV U DQVVQO RCTV CPF RWUJ KV KPVQ KVU EQTTGEV RQUKVKQP WPVKN [QW JGCT C
ENKEM KPFKECVKPI KV KU RTQRGTN[ ZGF [Fig. 15]
NOTE: Remove the water tank when the robot is charging or not in use.
NOTE: 6Q GPJCPEG VJG ENGCPKPI TGUWNV CPF VQ CEJKGXG CP GSWCN FKUVTKDWVKQP QH YCVGT QPVQ VJG QQT KV KU
necessary to soak the cleaning cloth under running water and slightly wring it out, before attaching it to
MAX VJG YCVGT VCPM 6JKU GPJCPEGU GSWCN QY QH YCVGT HTQO VJG YCVGT VCPM VJTQWIJ VJG ENGCPKPI ENQVJ
WARNING: Water will start to drip out of the attachment, as soon as the water tank has been inserted. Start
Fig. 14
VJG ENGCPKPI RTQEGUU KOOGFKCVGN[ CHVGT KPUGTVKPI VJG YCVGT VCPM UQ CXQKF RQUUKDNG FCOCIGU VQ VJG QQT
Due to the same reason, remove the water tank directly after the cleaning process has ended.
#NYC[U UWRGTXKUG VJG RTQFWEV FWTKPI VJG ENGCPKPI VQ RTGXGPV YCVGT FCOCIGU VQ VJG QQTKPI KP ECUG VJG
robot should get stuck.
4. After mopping , remove the water tank and the mop. Open the rubber cap and pour remaining water
out of the tank. [Fig. 16]
5. Remove the mop from the water tank and wash it with delicate detergent and rinse it off. Wring the
mop and let it dry.
MAINTAINING YOUR ROBOT CLEANER
EMPTYING THE DUST CONTAINER
After vacuuming, remove the dust container.
1. Press the release button and pull it out. [Fig. 17]
Fig. 15
2. Hold the dust container over a dust bin. [Fig. 18]
3. Use the cleaning brush when necessary to remove any excess dust from the internal surface of the
FWUV EQPVCKPGT QT VGT UWTHCEG
 4G V VJG FWUV EQPVCKPGT VQ VJG Robot.
CLEANING THE FILTERS
6JG TQDQV KU VVGF YKVJ C RTGOQVQT NVGT 6Q OCKPVCKP QRVKOWO ENGCPKPI RGTHQTOCPEG TGIWNCTN[
ENGCP VJG NVGT EQXGT VJG RTGOQVQT NVGT CPF VJG URQPIG NVGT 6JG[ UJQWNF DG ENGCPGF GXGT[  FWUV
container empties and should not be washed.
1. Turn the robot off and remove from the charging station.
Fig. 16
2. Press the dust container release button and remove the dust container from the Robot. [Fig. 17]
 4GOQXG CNN NVGT EQORQPGPVU CPF ENGCP VJGO UGRCTCVGN[ 6JG CUUGODN[ KU FQPG KP TGXGTUG
order. [Fig. 19]
/CMG UWTG VJCV VJG NVGT KPUGTV KU EQTTGEVN[ CUUGODNGF 6Q GPUWTG VJKU RTGUU VJG UJQTVGT UKFG YCNN KPVQ
VJG VVKPI TUV DGHQTG RWUJKPI KP VJG NVGT QP VJG QVJGT UKFGU D[ RTGUUKPI FQYP QP VJG GFIGU
IMPORTANT: 4GIWNCTN[ EJGEM CPF OCKPVCKP VJG NVGTU D[ HQNNQYKPI VJG NVGT OCKPVGPCPEG KPUVTWEVKQPU
This will maintain your RQDQV U RGTHQTOCPEG
CLEANING ANTI FALL SENSORS
To maintain the safe operation of your robot it is important to keep the Anti fall sensors clean.
Fig. 17
There are 3 sensors are located on the underside of the robot. Turn the robot upside down and clean
them with a soft brush to remove any accumulation of dust, dirt or debris. [Fig. 20]
Fig. 18
Fig. 19
GB
Fig. 20