A Ccessories (Sold Separately) - Oreck XL ORBITER Manual De Usuario

T
roubleshooting
WARNING: Unplug cord from
electrical outlet before servicing.
P P P P
ROBLEM OSSIBLE
ROBLEM OSSIBLE
F M Not plugged in
LOOR ACHINE
properly.
WILL NOT RUN
No electricity in
wall outlet.
Blown fuse/
tripped breaker
Motor circuit
breaker has
tripped.
F M Brush or pad
LOOR ACHINE
holder not
BOUNCES
properly in place.
Using brush on dry
surface without
dry shampoo or
wet shampoo.
Whenever calling, please be sure to have your model and
serial number from data plate.
A
ccessories (Sold Separately)
When choosing different pads and brushes for the Orbiter, there
is no exact science to which pad or brush is most suitable on a
particular floor. Pads are good for scrubbing and polishing flat
surfaces. Brushes work well for getting into recesses in non-flat
surfaces, like tile, where the bristles can get into grout lines.
When you choose an accessory, remember - you want one
aggressive enough to do the job but gentle enough not to
damage the floor. Use common sense. For example, do not use a
black pad (aggressive) on a wood floor (soft floor). Start with
what is safe and move to more aggressive, if needed.
The pads are color coded depending on how aggressive they are
(except for the beige marble pad): White is the softest, followed
by red, green, brown and black being the most aggressive. Pads
are designed to be porous and open-weave (except the beige
pad) so that when it loosens dirt it can pick it up. The dirt goes
inside the pad (i.e. off the floor). All pads can be turned over and
the other side used before cleaning and disposing. Pads may be
hosed off in some instances and re-used.
Brushes are also coded with black being the softest followed by
the union mix (tan) brush, the orange scrub brush, with the brown
grit brush being the most aggressive.
E N G
G
uide
S S A A C C
OURCE REAS TO HECK
OURCE REAS TO HECK
Be sure cleaner is
firmly plugged
into wall outlet.
Check electrical
source–fuse or
circuit breaker.
Replace fuse/
Reset breaker
Turn switch off
and unplug
cleaner. Check
motor shaft for
binding. Allow
30 minutes for
motor to cool and
system to reset. If
unit is equipped
with red reset
button, press it.
Place it properly.
(See operating
instructions.)
Apply necessary
shampoo dry or
wet.
L I S H
Note: Never store the Orbiter with a pad or brush mounted on it
because they can become deformed especially the brushes.
DRIVE PADS
DRIVE PAD HOLDER (Black plastic with teeth)
FLOOR PADS
POLISHING PAD (White)
SCRUB PAD (Brown)
STRIP PAD (Black)
BUFFING PAD (Red)
CLEANING PAD (Green)
For all floor pads, place either DRIVE PAD HOLDER or DRIVE PAD
BRUSH on Orbiter. Then place the pad on the floor and center
Orbiter onto the pad.
FLOOR BRUSHES
SHAMPOO BRUSH (Black bristle)
Use with ORECK DRY SHAMPOO. This brush has specially cut
bristles to provide safe, soft action needed for carpet cleaning.
POLISHING BRUSH - UNION MIX (Tan bristles) 237048
This polishing brush can be used to polish wood floors. This brush
will "blend" in excess floor wax, maintain an even coat of wax
and eliminate wax buildup.
SCRUB BRUSH (Orange bristles)
This brush is used to clean ceramic and concrete and many tough
stains.
GRIT BRUSH (Hard green/gray bristles)
This is an extremely aggressive brush used to scour tough stains
on concrete and asphalt.
All the floor brushes snap directly onto the Orbiter with no drive
pad. Remove the brushes from the machine after use so as not to
damage them.
OTHER ACCESSORIES
LAMBS WOOL BONNET
This bonnet is designed to provide the best possible shine on
wood, tile and vinyl floors. To install bonnet, place over the DRIVE
PAD HOLDER. Pull the drawstrings tight to prevent slipping. Tie a
bow and tuck the excess string inside the bonnet. Use the bonnet
for everyday buffing to remove scuff marks. When the bonnet
becomes dirty, wash with soap and water, wring it out and place
it back on the DRIVE PAD HOLDER to dry to its original shape.
WHITE TERRYCLOTH BONNET
This bonnet cleans the traffic lane and spots in the carpet without
wetting the entire carpet. When one side of bonnet is dirty, flip it
over and use the other side. When bonnet is completely soiled,
hose off and air dry.
SAND SCREENS
The very best in floor sanding. For all sand screens, place either
DRIVE PAD HOLDER or DRIVE PAD BRUSH on Orbiter. Then place
the sand screen under any floor pad on floor and center Orbiter
onto the pad. The SAND SCREEN comes in 60 grit (SS12060),
80 grit (SS12080) and 100 grit (SS12100).
4
53178-51-0327
437051
437049
437071
437055
437056
237049
237047
237056
437054
437053