Important Safety Instructions; Technical Specifications - Televes T.OX Serie Guía Rápida

DVBS2-QAM HEXA

Important safety instructions

Caution Statements
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Warning
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
Safe operation
Should any liquid or object fall into the equipment, please refer to qualified personnel for
service.
Safe installation
Ambient temperature should not be higher than 45°C.
Do not place the equipment near heat sources or in a highly humid environment.
Do not place the equipment in a place where it can suffer vibrations or shocks.
Please allow air circulation around the equipment.
Do not place naked flames, such as lighted candles on or near the product.
Simbology
Equipment designed for indoor use.
The equipment meets the CE marking requirements.
The product is EAC certified.

Technical specifications

Input frequency
Input loop
Input level
Satellite
demodulator
Frequency steps
IN/OUT connectors
Input impedance
LNB power
S
atellite selection (DiSEqC)
Modulation format
Symbol rate
QAM
Modulator Roll-off factor
Block code
Output frequency
Frequency steps
Output loop
UP-Converter
Phase noise
Output level
Output level (selectable)
Consuptions 24V
(with signal)*
General
Protection index
It is estimated a power consumption of 300 mA from the LNB.
*
The technical characteristics described are defined for a maximum ambient temperature of 45 ° C (113 ° F). For higher temperatures forced ventilation will be used.
MHz 950 - 2150
ON/OFF
dBµV 60 a 115(-49 a -25 dBm)
MHz 1
Type "F" Female
Ohm 75
V
/kHz 13-17- OFF / 22kHz (ON-OFF)
16, 32, 64, 128, 256 QAM
Mbaud 1.5 - 7.2 max
% 15
Reed Solomon (188, 204)
MHz 46- 862 (Selec.)
kHz 250
ON/OFF
dBc/Hz 90@10kHz (typ.)
Without Loop: (100 ± 5)
dBµV
With Loop: (87 ± 5)
dB
A
IP
Inputs/Outputs/Connections description
The unit (Fig.1) is provided with:
1. IF satellite Input (PORT 1)
2. IF satellite Input/Output (PORT 2)
3. RF Input + 6 CH QAM (RF QAM 1)
4. RF Output + 6 CH QAM (RF QAM 2)
5. Power supply BUS connectors
6. Control BUS connectors
7. Ethernet upgrade connector
8. Programmer / PC connector
9. Status LED
10. Ethernet 1000 status LED
11. Ethernet 10/100 status LED
12. Satellite input status LED
13. QAM output status LED
Introduction
The DVBS2-QAM Hexa transmodulates the services coming form six satellite input
transponders into six DVB-C channels that can be freely placed in the 46-862 MHz
frequency range (channels C02 - C69 in the CCIR channel table).
The digital transmodulation process starts with the input satellite transponder
demodulation. The Transport Streams are obtained and subsequently modulated in QAM
format. Each output QAM channel is individually placed in the selected ouput frequency.
Input and output loops can be selected. Input loop provides the satellite signal to another
module when it is enabled, otherwise two independent inputs can be used.
The output loop in the QAM output allows the mixing of the output signal between
modules in the same subrack, or (when it is disabled) to have a single QAM output
providing a higher output level.
The Transport Stream processing in each module includes the services elimination, in the
case the satellite input rate is too hight to be accommodated in an output QAM signal.
The user can choose the input services that will be distributed in the output, deleting
the unwanted ones and thus reducing the output symbol rate. This filtering capability
also includes each individual component of a service (audio, subtitle, data), which can be
selected to be filtered off on a PID basis.
For each output service can be assigned a channel number (LCN, Logical Channel Number),
that facilitates the search of the services on the TV set. Each module allows the substitution
of the operator_id field (if it is present in the input) and it can set the versions of the SDT
table for each output and the shared NIT table for all the outputs. In this way, the cases
which the TVs show that a new channels scan must be placed will be decreased. Also, using
a shared NIT allows the tunning of all the services when an automatic scan is selected.
In the end, it is allowed to edit the value of the transport_stream_id and original_network_
id for each output and network_id and network_name which are shared for all the outputs.
Modulation
dB
Through losses
Symbol Rate Mbaud
FEC inner code LDPC
FEC outer code
Roll-off factor %
R.O.E. inner (min) dB
A, B, C o D
Scrambling
Interleaving
Bandwich MHz
Out spectrum
Step losses dB
Return losses dB
Input / Output Connectors Type
Output impedance Ohm
Spurious level dBc
> 15
0,95 (without LNB)
1,20 max (1LNB active)
1,45 max (both LNBs actives)
20
DVB-S2 (QPSK, 8PSK)
DVB-S (QPSK)
< 2.5 (typ.)
2 - 45(DVB-S)
2 - 33(DVB-S2)
(9/10, 8/9, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2)
BCH(Bose-Chaudhuri-Hocquenghem)
20, 25, 35
6 (typ.)
DVB ET300429
DVB ET300429
8.28 max (7.2 Mbaud)
Normal / Inverted (Selec.)
< 2.5 (typ.)
> 10 (typ.)
"F" Female
75
55min. > 60 (typ.)
6