Matco Tools MT2868 Instrucciones De Operación página 2

faIlure TO OBserVe These WarnIngs cOuld resulT In InJury
ThIs InsTrucTIOn
IMPOrTanT safeTy InfOrMaTIOn.
read ThIs InsTrucTIOn Manual carefully
and undersTand all InfOrMaTIOn BefOre
OPeraTIng ThIs TOOl.
• Always operate, inspect and maintain this tool in
accordance with American National Standards Institute
Safety Code of Portable Air Tools (ANSI B186.1) and any
other applicable safety codes and regulations.
• For safety, top performance and maximum durability of
parts, operate this tool at 90 psig; 6.2 bar max air
pressure with 3/8" diameter air supply hose.
• Always wear impact-resistant eye and face protection
when operating or performing maintenance on this tool.
• Always wear hearing protection when using this tool.
High sound levels can cause permanent hearing loss.
Use hearing protection as recommended by your
employer or OSHA regulation.
• Keep the tool in efficient operating condition.
• Operators and maintenance personnel must be
physically able to handle the bulk, weight and power of
this tool.
• Air powered tools can vibrate in use. Vibration, repetitive
motions or uncomfortable positions over extended
periods of time may be harmful to your hands and arms.
Discontinue use of tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Air under pressure can cause severe injury. Never direct
air at yourself or others. Always turn off the air supply,
drain hose of air pressure and detach tool from air supply
before installing, removing or adjusting any accessory
on this tool, or before performing any maintenance on
this tool. Failure to do so could result in injury. Whip
hoses can cause serious injury. Always check for
damaged, frayed or loose hoses and fittings, and replace
immediately. Do not use quick detach couplings at tool.
See instructions for correct set-up.
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
OPeraTIOn
The sander has a reciprocating pad and produces a smooth and
professional finish to most surfaces. Suitable for removing paint and
rust from metal surfaces, smoothing edges, shaping welded surfaces
including fiberglass and wood surfaces for further finishing.
Abrasive paper can be held by 2 clamps or PSA paper. Do not use the
tool for any other purpose than that for which it was designed. Do not
modify the tool for any other purpose.
Speed can be varied by the trigger (23). Always disconnect air supply
when changing sandpaper. Apply light pressure to the work area and
allow the sandpaper to provide the desired finish.
MT2868
MT2868 DUAL PISTON STRAIGHT LINE SANDER
Manual cOnTaIns
WARNING
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Sanding pad may continue to reciprocate briefly after
throttle is released. Avoid direct contact with sanding
pad during and after use. Gloves will reduce the risk of
cuts or burns.
• Keep away from reciprocating sanding pad. Do not wear
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories.
• Use accessories recommended by Matco Tools.
• Do not lubricate tools with flammable or volatile liquids
such as kerosene, diesel or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
• This product may contain one or more chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm. Wash hands
thoroughly after handling.
Be careful when sanding around sharp edges to prevent cutting
sandpaper and pad. Change sandpaper when worn or clogged. Use
sandpaper specifically sized to the pad.
Periodically check air inlet screen and remove any contaminants
2 03/19/12