Important Safety Instructions; Agency Approvals; Specifications; Operating Conditions - BriskHeat XtremeFLEX HSTAT Serie Manual De Instrucciones

IMPORTANT SAFETY INSTRUCTIONS

DANGER
A person who has not read and
understood all operating
Instructions is not qualified to
operate this product.
DANGER

Do not immerse heater in liquid.

For indoor use only.

Keep volatile or combustible material away from
heater when in use.

Use heater only in approved locations.

Keep sharp metal objects away from heater.
Failure to observe these warnings may result in electric
shock, risk of fire, and personal injury.
WARNING
End-User Must Comply to the Following:

Only qualified personnel are allowed to connect
electrical wiring.

Disconnect all supply power at the source before
making any power connections.

All electrical wiring must follow local electrical
codes and highly recommend following NEC
Article 427.

The person who performs the final installation /
wiring must be qualified for this work.

The end-user is responsible for providing a
suitable disconnecting device.

The end-user is responsible for providing a
suitable electrical protection device. Ground Fault
Equipment Protection is required.
Failure to observe these warnings may result in personal
injury or damage to the heater.
®
© BriskHeat Corporation. All rights reserved.
®
XtremeFLEX HSTAT
Silicone Rubber Heating Tape

Agency Approvals

Approvals valid only when installed in accordance with
all applicable instructions, codes, and regulations.
CAUTION

Never handle the heating tape while it is in
operation; always disconnect the heating tape
from the power source and allow to cool prior to
handling.

Inspect heating tape before use.

Do not use heating tape with torn or worn
surfaces.

Do not wrap the heater over itself

Do not repair damaged or faulty heaters.

Do not crush or apply severe physical stress on
heater or cord assembly.

Unplug heater when not in use.

Fasten heater to device using approved methods
only.

If spillage of foreign matter onto heater occurs,
disconnect from power source and clean after
heater has been allowed to cool.

Never operate a heater without an appropriate
heat sink (device being heated is considered a
heat sink).

Make sure there is a uniform fit prior to energizing.
If there are air gaps between the surface to be
heated and the heater, hot spots can occur that
could result in burnouts due to overheating.
Failure to observe these warnings may result in personal
injury or damage to the heater.
3

SPECIFICATIONS

Operating conditions:


Maximum Exposure Temperature: 450°F (232°C)

Minimum Exposure Temperature: -40°F (-40°C)

Adjustable Thermostat Control 50-425°F (10-218°C)

120 or 230VAC Models

2
Power Density: 6.0 watts/in (0.009 watts/mm

Moisture and Chemical Resistant

Suitable for Electrically Conductive Surfaces

120VAC model includes NEMA 1-15 plug

230VAC model includes crimped wire ferrule terminals
Width Length Total
in (mm) in (mm) Watts
24.0 (610) 72
48.0 (1220) 144
0.5 (13) 72.0 (1830) 216
96.0 (2440) 288
120.0 (3050) 360
24.0 (610) 144
48.0 (1220) 288
1.0 (25) 72.0 (1830) 432
96.0 (2440) 576
120.0 (3050) 720
24.0 (610) 288
48.0 (1220) 576
2.0 (51) 72.0 (1830) 864
96.0 (2440) 1152
120.0 (3050) 1440
24.0 (610) 432
48.0 (1220) 864
3.0 (76) 72.0 (1830) 1296
96.0 (2440) 1440
120.0 (3050) 1440/1800
®
© BriskHeat Corporation. All rights reserved.
®
XtremeFLEX HSTAT
Silicone Rubber Heating Tape
2
)
Part Number
Part Number
230VAC
120VAC
(No plug)
HSTAT051002 HSTAT052002
HSTAT051004 HSTAT052004
HSTAT051006 HSTAT052006
HSTAT051008 HSTAT052008
HSTAT051010 HSTAT052010
HSTAT101002 HSTAT102002
HSTAT101004 HSTAT102004
HSTAT101006 HSTAT102006
HSTAT101008 HSTAT102008
HSTAT101010 HSTAT102010
HSTAT201002 HSTAT202002
HSTAT201004 HSTAT202004
HSTAT201006 HSTAT202006
HSTAT201008 HSTAT202008
HSTAT201010 HSTAT202010
HSTAT301002 HSTAT302002
HSTAT301004 HSTAT302004
HSTAT301006 HSTAT302006
HSTAT301008 HSTAT302008
HSTAT301010 HSTAT302010
4