Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Thank you for purchasing this Vollrath equipment. Before operating the
equipment, read and familiarize yourself with the following operating
and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. Save the original box and packaging. Use this packaging
to ship the equipment if repairs are needed.
SAFETY PRECAUTIONS
To ensure safe operation, read the following statements and understand
their meaning. This manual contains safety precautions which are
explained below. Please read carefully.
WARNING
Warning is used to indicate the presence of a hazard that will or can
cause severe personal injury or death.
CAUTION
Caution is used to indicate the presence of a hazard that will or can
cause minor or major personal injury if the caution is ignored.
NOTICE: Notice is used to note information that is important but not
hazard-related.
TOOLS YOU WILL NEED
• #2 Phillips Screwdriver
• Drill
• ¹⁄₈" Drill Bit (For #29 Pilot Hole)
• Sabre Saw or Hand Router
• 3 #8 x 1.00" Pan Head Phillips Screws (included)
CHOOSE THE CORRECT SPRING
The dispenser includes two springs for different applications. See the
chart below. The lighter weight dispenser is factory installed. See
"Change Default Spring (Optional)" on page 3.
Mounting
Dispensing
Paper or Plastic
Vertical
Foam
Horizontal
Paper, Plastic or Foam
Paper or Plastic
Angled
Foam
Installation Instructions
Spring Loaded In-Counter Cup Dispenser
Item No.
CADJ-1
CADJ-2
CADJ-3
CADJ-4
INSTALLATION
Mount the Dispenser
1. Cut the appropriate diameter opening in the mounting surface.
2. Lift the bezel to remove it from the tube to revel the mounting holes
and the components that can be adjusted to accommodate different
cup diameters.
Use This Spring
Heavier Weight
Lighter Weight
Lighter Weight
Heavier Weight
Lighter Weight
©
2017 The Vollrath Company L.L.C.
For Cup Rim Diameter
Cutout Diameter
2¹⁄₂ – 3¹⁄₂" (6.4 – 8.9 cm)
3 – 3⁷⁄₈"(7.6 – 9.8 cm)
3 – 4⁵⁄₈" (7.6 – 11.7 cm)
4¹⁄₂ – 5¹⁄₄" (11.4 – 13.3 cm)
Part No. 350719-1 ml
4 (10.2)
4¹⁄₂ (11.4)
5¹⁄₄ (13.3)
5³⁄₄ (14.6)
3/30/17
Publicidad
Manuales relacionados para Vollrath CADJ-1
Resumen de contenidos para Vollrath CADJ-1
- Página 1 Installation Instructions Spring Loaded In-Counter Cup Dispenser Thank you for purchasing this Vollrath equipment. Before operating the equipment, read and familiarize yourself with the following operating and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Save the original box and packaging. Use this packaging to ship the equipment if repairs are needed.
- Página 2 3. Insert a short stack of cups into the dispenser. 5. Remove the dispenser from the mounting hole. 6. Pre-drill pilot the pilot holes. Vollrath suggests a ¹⁄₈" (0.125) diameter pilot hole diameter of ¹⁄₈" (0.125). 4. Rotate the adjusting ring until the cups are held in place.
- Página 3 5. Lightly tighten one of the adjusting ring screws to hold the ring in CHANGE DEFAULT SPRING (OPTIONAL) place. 1. Pull off the retaining ring from the bottom the dispenser. Remove the end cap. Adjusting NOTICE: Notice the cap is under pressure from the spring. Adjusting ring screw ring screw...
- Página 4 WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C. This warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written warranty to purchasers for such uses.
- Página 5 Utiliser ce Montage Distribution ressort Papier ou plastique Forte pression Vertical Mousse Faible pression Horizontal Papier, plastique ou mousse Faible pression Papier ou plastique Forte pression Incliné Mousse Faible pression © 2017 The Vollrath Company L.L.C. Num. d’art. 350719-1 ml 3/30/17...
- Página 6 3. Insérez une petite pile de gobelets dans le distributeur. 5. Retirez le distributeur du trou de fixation. 6. Pré-percez les trous de guidage. Vollrath suggère un diamètre de trou de guidage de ¹⁄₈" (0,125). 4. Tournez l’anneau de réglage jusqu’à ce que les gobelets soient bien en place.
- Página 7 5. Serrez légèrement une des vis de l’anneau de réglage pour maintenir REMPLACEMENT DU RESSORT PAR DÉFAUT celui-ci en place. (EN OPTION) 1. Retirez l’anneau de blocage par le bas du dsitributeur. Retirez le Vis de capuchon. Vis de l’anneau l’anneau AVIS : Notez que le capuchon est sous la pression du ressort.
- Página 8 Vollrath. Lorsque vous contacterez les services techniques de Vollrath, tenez-vous prêt à fournir le numéro d'article, le numéro de modèle (s'il y a lieu), le numéro de série et le justificatif d’achat indiquant la date d’achat de l’appareil.
- Página 9 Instrucciones de instalación Dispensador de vasos a resorte en mostrador Gracias por comprar este equipo Vollrath. Antes de usar el equipo, lea y familiarícese con las siguientes instrucciones de operación y seguridad. CONSERVE ESTAS INSTRUCCIONES COMO REFERENCIA PARA EL FUTURO. Conserve la caja y embalado originales. Deberá utilizarlos para devolver el equipo en caso de que requiera reparaciones.
- Página 10 3. Inserte una pequeña pila de vasos en el dispensador. 5. Retire el dispensador del orificio de montaje. 6. Preperfore los orificios piloto. Vollrath sugiere utilizar un diámetro de agujero piloto de ¹⁄₈" (0,125). 4. Gire el anillo de ajuste hasta que los vasos queden sujetos en su lugar.
-
Página 11: Limpieza
5. Apriete levemente uno de los tornillos del anillo de ajuste para CAMBIE EL TORNILLO PREDETERMINADO sujetar el anillo en su lugar. (OPCIONAL) 1. Desprenda el anillo de retención en la parte inferior del dispensador. Tornillo Retire la tapa extrema. Tornillo del anillo del anillo... - Página 12 CLÁUSULA DE GARANTÍA DE THE VOLLRATH CO. L.L.C. Esta garantía no se aplica a los productos adquiridos para uso personal, familiar ni doméstico, y The Vollrath Company LLC no ofrece una garantía por escrito a los compradores para dichos usos.