Please read carefully and save these
instructions as you may need them at a later
GENERAL: All electrical connections must be in accordance
with local and National Electrical Code (N.E.C.) standards. If
you are unfamiliar with proper electrical wiring connections
obtain the services of a qualified electrician.
Remove the trim from the box and make sure that no parts are
missing by referencing the PARTS illustrations.
THIS
RETROFIT
ASSEMBLY
COMPONENT
OF
A
LED
SUITABILITY
OF
THE
DETERMINED BY CSA OR CANADIAN AUTHORITIES
HAVING JURISDICTION.
_________________________________________________
WARNING- RISK OF FIRE OR ELECTRIC
SHOCK
FOR USE WITH INCANDESCENT HOUSING MODELS:
COMMERCIAL
ELECTRIC
HBR2000BICAT;
HALO H99T, H99RT, H99ICT, H99TAT,
H99RTAT, H99ICAT; CORDELIA X2000LICAT, X2000LRICAT,
X2000LICATB; CAPRI R4, RR4; ELCO EL99A, EL99RA,
EL99ICA; JUNO TC1, TC1R; LITHONIA L3, L3R; PROGRESS
P832-TG, P830-TG; THOMAS PS4, PS4-RM; NORA NSCIC-
40IAT; ELITE B4, 4R. HALO LED HOUSINGS – H995ICAT,
H995RICAT.
•
Do not alter, relocate, or remove wiring, lampholders, power
supply, or any other electrical component. Installation of
the retrofit assembly requires a person familiar with the
construction and operation of the luminaire's electrical
system and the hazard involved. If not qualified, do not
attempt installation. Contact a qualified electrician.
•
Do not make or alter any open holes in an enclosure of
wiring or electrical components during kit installation.
•
To prevent wiring damage or abrasion, do not expose
wiring to edges of sheet metal or other sharp objects.
____________________________
ASSEMBLY AND INSTALLATION
INCANDESCENT HOUSINGS
1. Unscrew the WING NUT inside the CAN to detach the
SOCKET BRACKET from the CAN. Disengage the
SOCKET from the SOCKET BRACKET. (FIG. 1)
2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 2)
3. Plug the FEMALE CONNECTOR of the RETROFIT TRIM
onto the MALE CONNECTOR of the SOCKET ADAPTER
ASSEMBLY. (FIG. 3)
4. Tuck all wires into the CAN and carefully push the
RETROFIT TRIM into CAN. (NOTE: To provide enough
room
in
shallow
cans,
ADAPTER and SOCKET adjacent to the side of the LED
DRIVER prior to inserting the RETROFIT TRIM into the
CAN.) (FIG. 4)
LED HOUSINGS
1. Plug the FEMALE CONNECTOR of the RETROFIT TRIM
onto the MALE CONNECTOR of the HALO HOUSING.
(FIG. 3)
2. Tuck all wires into the CAN and carefully push the
RETROFIT TRIM into CAN. (FIG. 4)
LED 4" RETROFIT TRIM INSTALLATION
INSTRUCTIONS - MODEL EVL4730M
date.
IS
ACCEPTED
LUMINAIRE WHERE THE
COMBINATION
SHALL
HBR2000B,
HBR2000R,
carefully
position
SOCKET
ALL RIGHTS RESERVED Envirolite 2015
WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT
MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE
INSTALLING OR SERVICING THE FIXTURE.
PARTS
AS
A
SOCKET ADAPTER
ASSEMBLY
BE
RETROFIT TRIM
Driver Screws
QUESTIONS? CALL TOLL
1-855-573-6156
FREE
COMPATIBLE HOUSING
DIMENSIONS
4 in.
FIG. 1
FIG. 3
FIG. 5
FIG. 2
FIG. 4
FIG. 6
REV 08-DEC-15