Palram Olympia 3x4.25 Manual Del Usuario página 9

Notes
During Assembly
Use
a
soft platform below the parts to avoid scratches and damages.
Please note you install the panels
with
the
UV
protected
side
out (marked with
"THIS
SIDE
OUT")
111'
remove plastic film before inserting panels and locking
in place.
If
the
panels received
with the product
are clear
/
white,
please remove
only the plastic sticker
as
panels are locked in place.
Product dimensions
can be
adjusted to your specific needs:
1. The
wall-mounting profile (top-back)
can be
adjusted from 260 to
305 cm
(102.4" to 120") above ground. The adjusting
is
done
when measuring and drilling (Step
5).
Please note the installation recommendations' height suggested in
Diagram
A.
Please
note that the product appearance may slightly change
as a
result,
however snow load weight does not change.
2.
Poles
distance from the wall can be adjusted from 226
to 286
cm
(89" to 112.6")
as
suggested in
Diagram
B1.
Poles
distance from the
side edges can be
adjusted from
5
to
54 cm
(2" to 21.6")
as
suggested
in
Diagram
B2.
The adjusting
is
done after assembly and before anchoring (Step 24) by sliding poles and profile 7040+7041 at the roof profiles'
channels.
3. Wall
mounting
and distance from the wall determine the roof angle and the total depth
of
the product (distance
of gutter
from
the wall). Higher wall mounting and shorter distance between wall and
poles increase
the roof angle and shorten the total depth
as
suggested
in
Diagram
C.
Steps
Step
7: It
is
important to plan the installation
area,
mark
as
per the instructions and level the surface prior to the assembly.
Make sure you use
suitable
screws and anchors.
Step 13:
Please
apply silicone
sealants
above beam 7288
+
7290,
in
order to prevent water from seeping
in.
Step 15: Make sure
that the angle between the
back wall
profile and the panel supporting profiles
is
90 degrees.
Step
17 + 18: Please
note you install the panels with the
UV
protected
side
out (marked with
"THIS SIDE OUT")
remove plastic sticker
as
panels are locked
in place. If
the panels received
with the product
are
clear
/
white, please remove
only the plastic sticker
as
panels are
locked
in place.
Step 21b:
Please apply silicone sealants on both sides
of the part combining
8071 & 8072 in order to prevent water leakage,
as
shown at the drawing 19b.
Step 22a:
Please
apply silicone sealants on the inner part of 7997, and connect to the profile
as
depicted
in
drawing 20a.
Step 22c:
Please
do not tighten screw 4043
yet, in
order to allow the final adjustments done
in
step 24b.
Step 24a+24c:
Please
adjust the poles (inside out and sideways) by sliding them to their final position prior to anchoring. Make
sure
that the
poles
distance from the
Patio cover side edge does not exceed 54 cm/21.3".
Step 24b:
Please
adjust the
gutter
head's angle according to your needs and tighten
screws
4043.
Step 26: Anchoring this product to the ground
is
essential to its
stability and rigidity.
It is
required to complete this
stage in
order for your warranty to
be
valid.
*Tighten
all screws when completing assembly.
Note:
The wall anchoring kit supplied
with
this product
is
suitable for concrete or solid brick walls
only.
Other wall types need
an
accordant wall fixation kit.
II
260-305cm
102.4"-120"
B1
226-286cm
89"- 112.6"
.
.
17°
.
13°
+
*;
+