Flex-a-Lite 30 Manual De Instrucciones

Model 30 or 35 Electric Fans
Model 30: Puller mode, includes thermostatic control.
Model 35: Puller mode, does not include controls.
Mounting Instructions
installed either horizontally or vertically to the radiator.
1. Remove the vehicle's existing fan and shroud.
2. Position the electric fan against the back of the radiator
(between the radiator & engine), and mark the holes for
mounting.
3. Rotate the blades to make sure they are free of obstructions.
4. With a small phillips screwdriver, pass through the marked
holes, carefully spreading the fins to allow easy passage for the
nylon bolts.Pass the bolts through the shroud holes then twist
the bolts through the radiator.
Important: If using a model 30, be sure the thermostatic
sensing bulb is touching the radiator.
5. Install rubber disc spacers, washers, and speed nut. Cut the
excess off the bolt (Leave enough excess for adjustments).
Mandatory Connections for Model 30
1. Disconnect battery.
2. Connect the positive "+" terminal to a low amp 12 volt
positive (+) power source (e.g. fuse box), using the wire
provided in the kit.
Note(optional): Attach positive (+) terminal to an igni-
tion source to stop the fan unit from operating after the
engine is turned off.
3. Connect the "B" terminal to a high amp 12 volt positive (+)
power source, ie. positive (+) side of battery or alternator,
using the wire and inline fuse included in kit .
4. Connect the "G" terminal to ground (ie. chassis, negative (-
) side of battery) using the wire provided in the kit.
5. With the wire and 3-way connector provided, splice into
the A/C clutch positive(+) wire. Connect the other end of
the wire to the "C" terminal of the control box. Air Condi-
tioning Relay Activates fan when A/C is turned on.
6. Install provided knob onto the thermostat shaft.
7. Adjust thermostat to desired temperature within 180
Optional Connection
Manual Switch(not included)—Allows manual
operation of fan
(Note: based on Flex-a-lite's manual
switch part #31148)
1. Connect the "M" terminal to terminal 1 on the switch.
2. Attach terminal 2 to a 12 volt positive (+) source.
3. Attach terminal 3 to ground to illuminate switch.
Note (optional): To stop the fan from activating
thermostatically, omit the lead to the positive(+)
terminal of the control box. B, G, & M must remain
connected.
--
Model 30 or 35 may be
0
-240
Diagram A
Speed Nut
Rectangular
Rubber Washer
Mandatory Connections
+ 12 volt low amp source
G Ground
In Line Fuse
12 Volt Positive
Câblages obligatoires
+ Source 12 V basse intensité
G Terre
Fusible en ligne
0
.
Source 12 V (+)
Conexiones obligatorias
+ Fuenta positiva de 12
voltios y bajo
amperaje
Fuente de 12
voltios (+)
B 12 volt high amp
source
C Air conditioning relay
3-way
Control Box
Connector
C
M
B
12 Volt Source
Ground(Illuminate switch)
B Source 12 V haute
intensité
C Relais de climatisation
Connecteur à
Boîtier de contrôle
3 broches
C
M
B
Source 12 V basse intensité
Source 12 V
Terre (éclairage du commutateur)
G Tierra
B Fuente de 12 voltios y
elevado amperaje
C Relé (relevador) de aire
acondicionado
Conector en
Caja de control
tres sentidos
C
M
B
Fuente de 12 voltios y bajo
amperaje
Fusible en línea
Fuente de 12 voltios
Tierra (iluminación del interruptor)
1 of 2
Nylon Bolt
Plastic
Washer
Optional Connection
M Manual switch
Ground
G
+
12 Volt Low Amp Source
Câblage facultatif
M Commutateur manuel
Terre
G
+
Conexión opcional
M Interruptor manual
Tierra
G
+