1. Manuales
  2. Marcas
  3. Osborne Manuales
  4. Alimentadores de Alambre
  5. Big Wheel RN4 Serie
  6. Instrucciones de armado y operación

Osborne Big Wheel RN4 Serie Instrucciones De Armado Y Operación

Comedero para recria
Ocultar thumbs
1
2
3
4
5
6
7
8
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
Big Wheel
Osborne Big Wheel hog feeders are packaged carefully and compactly to ensure
their safe arrival at minimum cost. Each part was quality inspected prior to
shipment and each carton was carefully packed to ensure that all necessary
parts were present for the assembly.
Upon receiving your shipment, check the cartons for in transit handling damage.
ALERT THE DELIVERING CARRIER IMMEDIATELY if damage is discovered.
Continue unpacking only after the carrier has acknowledged the damage and
potential loss of contents.
All loss or damage in transit is the responsibility of the delivering carrier,
NOT OSBORNE INDUSTRIES. To protect your rights in the event of damage
or loss, sign the delivery waybill only after the carrier has acknowledged in writing that damage or loss has occurred. In the event that damage is
revealed only after unpacking is complete, notify the delivering carrier immediately and request an inspection of the damaged merchandise before proceeding.
ASSEMBLY AND OPERATING INSTRUCTIONS:
1.
Install axle (Item 9) into center recess of trough (Item 11). Drill 3/16-in.
holes through trough using axle as guide. Secure using 10-24 flat head
machine screws and 10-24 nuts (Items 10 & 12).
3.
Force trough divider cage (Item 3) onto trough using rubber mallet.
Ensure no gaps exist between cage and trough as fiberglass could break
when bolts are installed.
Drill 1/4-in. holes through trough using cage as a guide. Install 1/4 x
5/8-in. bolts and 1/4-in. nuts (Items 6). DO NOT OVER-TIGHTEN BOLTS
ON FIBERGLASS.
Hog Feeders
®
UNPACKING
NOTICE
RN4 SERIES
NURSERY CONFINEMENT FEEDER
Assembly & Operating Instructions
cordless drill
1/4-in. drill bit
3/8-in. wrench
1/2-in. socket wrench
pliers
NOTE: Standard drill bits rapidly become dull when used on fiberglass. Ma-
sonry bits are recommended. Use thread-locker on all bolts.
2.
Place 3/4-in. feed wheel washer (Item 8) on axle followed by feed wheel
(Item 7). If wheel does not turn freely, check for and remove paint or
galvanizing residue.
4.
Attach 1/4 x 1 1/4-in. cage tightener bolt and 1/4-in. hex nut (Items 4) into
top of cage divider but do not tighten.
Required Tools
3/16-in. drill bit
1/2-in. wrench
9/16-in. wrench
screwdriver
rubber mallet
RLX-0533_G

Publicidad

Tabla de contenido
loading

Manuales relacionados para Osborne Big Wheel RN4 Serie

Resumen de contenidos para Osborne Big Wheel RN4 Serie

  • Página 1 Big Wheel Hog Feeders ® Osborne Big Wheel hog feeders are packaged carefully and compactly to ensure Required Tools their safe arrival at minimum cost. Each part was quality inspected prior to shipment and each carton was carefully packed to ensure that all necessary cordless drill 3/16-in.
  • Página 2 ANCHORING THE FEEDER For proper operation, all Osborne Big Wheel Feeders must be anchored securely to flooring. Anchor brackets, fasteners, and fenceline adapters are also avail- able from Osborne, ordered separately. Contact Osborne Customer Service.
  • Página 3 Button plug Bolt NOT extending into cone NOTE: Osborne recommends filling the cone with sand or equivelant material before using the feeder. Weighing the cone prevents it from NOTE: Do not allow bolt to extend into cone. If the bolt extends into cone unsetting from the axle when feed level in hopper is below cone.

  • Página 4: Parts List

    Bolt kit (includes trough divider bolt kit; stainless steel) KF-N3S006 Trough divider bolt kit (stainless steel) Additional accessories, like hopper lids and multiple options in fenceline adapters, are available from Osborne, ordered separately. P.O. Box 388 • Osborne, KS 67473 U.S.A. Phone: 1-800-255-0316 • Fax: 1-785-346-2194 sales@osborne-ind.com •...

  • Página 5: Comederos Big Wheel ® Para Cerdos

    La pérdida o daño durante el transporte es responsabilidad de la empresa de transporte, NO DE OSBORNE INDUSTRIES. Para proteger sus derechos en caso de daño o pérdida, firme la guía de despacho sólo después que la empresa de transporte haya reconocido el daño o la pérdida por escrito. En caso que el daño se conozca sólo al terminar de desempacar, informe inmediatamente a la empresa de transporte y solicite una inspección de la mercancía dañada antes de seguir.
  • Página 6 ANCLAJE DEL COMEDERO Para un funcionamiento correcto, todos los comederos Big Wheel de Osborne deben estar anclados al piso en forma segura. Osborne dispone de anclas, pernos y adaptadores para la reja, los que deben ser ordenados por separado. Comuníquese con Servicio a Clientes Osborne.
  • Página 7 Tapón El perno no se extiende dentro del cono NOTA: Osborne recomienda llenar el cono con arena o un material NOTA: No deje que el perno se extienda dentro del cono, pues limitará equivalente antes de usar. El peso evita que el cono se salga del eje el ajuste del cono.

  • Página 8: Comedero Para Recria

    KF-N3S006 Kit de pernos de la jaula (acero inox.) Accesorios adicionales, como tapas de comederos y opciones múltiples de adaptadores para rejas, están disponibles en Osborne y deben ser ordenados por separado. P.O. Box 388 • Osborne, KS 67473 U.S.A.

Tabla de contenido