Publicidad
Idiomas disponibles
Idiomas disponibles
Big Wheel
Osborne Big Wheel hog feeders are packaged carefully and compactly to
ensure their safe arrival at minimum cost. Each part was quality inspected
prior to shipment and each carton was carefully packed to ensure that all
necessary parts were present for the assembly.
UNPACKING
Upon receiving your shipment, check the cartons for in transit handling
damage. ALERT THE DELIVERING CARRIER IMMEDIATELY if damage is
discovered. Continue unpacking only after the carrier has acknowledged the
damage and potential loss of contents.
All loss or damage in transit is the responsibility of the delivering carrier, NOT
OSBORNE INDUSTRIES. To protect your rights in the event of damage or
loss, sign the delivery waybill only after the carrier has acknowledged
in writing that damage or loss has occurred. In the event that damage is
revealed only after unpacking is complete, notify the delivering carrier immediately and request an inspection of the damaged merchandise before proceeding.
ASSEMBLY AND OPERATING INSTRUCTIONS:
1.
Install axle (Item 9) into center recess of trough (Item 11). Drill 3/16-in.
holes through trough using axle as guide. Secure using 10-24 flat head
machine screws and 10-24 nuts (Items 10 & 12).
3.
Force trough divider cage (Item 3) onto trough using rubber mallet.
Ensure no gaps exist between cage and trough as fiberglass could break
when bolts are installed.
Drill 1/4-in. holes through trough using cage as a guide. Install 1/4 x
5/8-in. bolts and 1/4-in. nuts (Items 6). DO NOT OVER-TIGHTEN BOLTS
ON FIBERGLASS.
Hog Feeders
®
NOTICE
RN4 SERIES
NURSERY CONFINEMENT FEEDER
Assembly & Operating Instructions
Required Tools
cordless drill
1/4-in. drill bit
1/2-in. socket wrench
7/16-in. socket wrench
3/8-in. wrench
pliers
NOTE: Standard drill bits rapidly become dull when used on fiberglass. Ma-
sonry bits are recommended. Use thread-locker on all bolts.
2.
Place 3/4-in. feed wheel washer (Item 8) on axle followed by feed wheel
(Item 7). If wheel does not turn freely, check for and remove paint or
galvanizing residue.
4.
Attach 1/4 x 1 1/4-in. cage tightener bolt and 1/4-in. hex nut (Items 4) into
top of cage divider but do not tighten.
RLX-0533_H
3/16-in. drill bit
1/2-in. wrench
7/16-in. wrench
9/16-in. wrench
screwdriver
rubber mallet
Publicidad
Tabla de contenido
Manuales relacionados para Osborne Big Wheel RN4 Serie
Resumen de contenidos para Osborne Big Wheel RN4 Serie
- Página 1 All loss or damage in transit is the responsibility of the delivering carrier, NOT NOTE: Standard drill bits rapidly become dull when used on fiberglass. Ma- OSBORNE INDUSTRIES. To protect your rights in the event of damage or sonry bits are recommended. Use thread-locker on all bolts.
- Página 2 Bolt NOT extending into cone. NOTE: Osborne recommends filling the cone with sand or equivalent NOTE: Do not allow bolt to extend into cone. If the bolt extends into cone material before using the feeder. Weighting the cone prevents it from unsetting from the axle when feed level in hopper is below cone.
- Página 3 13. Place completed assembly into feeder hopper. Align cone onto axle as- 14. Ensure feed flow control (Item 13) is set to ‘0’. Remove bottom two (2) sembly. nuts and spring and set aside. 15. Place feed flow control onto crossbar with back side of assembly resting 16.
-
Página 4: Parts List
Trough divider bolt kit KF-N3S005 Bolt kit (includes trough divider bolt kit; stainless steel) KF-N3S006 Trough divider bolt kit (stainless steel) P.O. Box 388 • Osborne, KS 67473 U.S.A. Phone: 1-800-255-0316 • Fax: 1-785-346-2194 sales@osborne-ind.com • www.osbornelivestockequipment.com Printed in the U.S.A. -
Página 5: Comederos Big Wheel ® Para Cerdos
Instrucciones de armado y operación ® Los Comederos Big Wheel de Osborne han sido empacados en forma com- HERRAMIENTAS NECESARIAS pacta y con cuidado, para un transporte seguro al mínimo costo. Cada parte ha pasado por un cuidadoso control de calidad antes de ser despachada,... - Página 6 El perno no se extiende dentro del soporte del cono NOTA: Osborne recomienda llenar el cono con arena o un material equivalente antes de usar. El peso evita que el cono se salga del eje NOTA: No deje que el perno se extienda dentro del cono, pues limitará...
- Página 7 12. Coloque todo este armado dentro de la tolva. Alinee el cono sobre el eje. 13. Asegúrese que el control de flujo de alimento (ítem 13) esté en “0”. Rem- ueva las dos tuercas inferiores y el resorte, y dejar a un lado. 14.
-
Página 8: Lista De Partes
Kit de pernos de la jaula KF-N3S005 Kit de pernos (incluye pernos de la jaula, acero inox.) KF-N3S006 Kit de pernos de la jaula (acero inox.) P.O. Box 388 • Osborne, KS 67473 U.S.A. Teléfono: 1-785-346-2192 • Fax: 1-785-346-2194 sales@osborne-ind.com • www.osbornelivestockequipment.com Impreso en EE.UU.