Robern M Serie Instrucciones De Instalación

This instruction sheet contains information on how to install the Push-
to-Open mechanism on your M Series cabinet (each cabinet needs only
one kit). To install the Push-to-Open mechanism, follow these steps:
1. Position the supplied Jig opposite the hinges in a corner of the
cabinet. Be sure the fl ange of the Jig is pressed against the fl ange
of the cabinet as shown in Figure A.
NOTE: On MP and MT cabinets, the Push-to-Open mechanism may be
placed at either the upper or lower corner, however on MF Full Length
cabinets, the Push-to-Open mechanism must be installed in the upper
corner of the lower cabinet.
2. Using the supplied Drill Bit, drill four holes into the
side of the cabinet using the Jig holes shown in
Figure A.
3. Remove the Jig and position the Push-to-Open
Base Plate so all four screw holes on the plate
line up with the drilled holes (if they don't line up,
fl ip the Base Plate over). Use the supplied screws
and the #1 Phillips Bit to install the four screws as
shown in Figure B.
NOTE: Be sure to use the supplied #1 Phillips Bit so the
screws do not become stripped.
4. Slide the Push-to-Open Cylinder into the Base
until it snaps into place as shown in Figure C.
5. Adjust the bumper on the Cylinder so the door
closes properly by turning the bumper clockwise or
counterclockwise.
Parts List / Liste des pièces / Lista de partes
Base Plate and Cylinder
Plaque de base et cylindre
Placa base y cilindro
4 Phillips Head screws
4 vis à tête Phillips
4 tornillos Phillips con cabeza chata
Make sure that you have all the contents listed in the Parts List. If you
experience any problems with your cabinet, contact your dealer or Robern
directly. / Assurez-vous d'avoir tous les éléments cités dans la Liste des
pièces. Si vous éprouvez un problème quelconque avec votre armoire,
contactez votre marchand ou communiquez directement avec Robern. /
Asegúrese de tener todo el contenido listado en la Lista de partes. Si
usted tiene algún problema con su gabinete, póngase en contacto con su
distribuidor o directamente con Robern.
Cabfax 1101
M SERIES PUSH-TO-OPEN KIT
INSTALLATION INSTRUCTIONS
Jig
Gabarit
Gálibo
Drill Bit
Foret
Broca
#1 Phillips Bit
Foret Phillips #1
Broca Phillips del #1
JIG
GABARIT
GÁLIBO
FLANGE
BRIDE
PESTAÑA
Figure B
4 SCREWS
BASE
4 VIS
PLATE
4 TORNILLOS
PLAQUE
DE BASE
PLACA
BASE
Limited Warranty One Year Term
ROBERN warrants to the original purchaser that, it will, at its election repair,
replace, or make appropriate adjustment to products made by this company
shown to have signifi cant defects in material or workmanship which are reported
to ROBERN in writing within one (1) year from the date of delivery. ROBERN is not
responsible for installation costs.
The warranty is void in the event the product is damaged in transit, or if damage
or failure is caused by abuse, misuse, abnormal usage, faulty installation, damage
in an accident, improper maintenance, or any repairs other than those authorized
by ROBERN. At the expiration of the one year warranty period, ROBERN shall be
under no further obligation under any warranty, expressed or implied, including the
implied warranty of merchantability.
ROBERN shall not be liable for any consequential damages arising out of or in
connection with the use or performance of its products. Some states do not allow
limitations on how long an implied warranty lasts or do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Any liability against ROBERN under any implied warranty, including the warranty
of merchantability, is expressly limited to the terms of this warranty. Permission
to return any merchandise under this warranty must be authorized by ROBERN
and returned prepaid by the purchaser. Claims under this warranty should be sent
directly to your dealer.
Robern • 701 N. Wilson Ave • Bristol, PA 19007
1-800-877-2376 • FAX 1-215-826-9666
1
ENGLISH / FRANÇAIS / ESPAÑOL
Robern
701 N. Wilson Ave.
Bristol, PA 19007
1.800.877.2376
Figure A
JIG HOLES
(4 IN A LINE)
TROUS DE
GABARIT
(4 EN LIGNE)
AGUJEROS
DEL GÁLIBO
(4 EN UNA
LÍNEA)
Figure C
SLIDE CYLINDER INTO
BASE PLATE
BUMPER GLISSER LE CYLINDRE
DANS LA PLAQUE DE
BUTOIR
BASE
TOPE
DESLICE EL CILINDRO
EN LA PLACA BASE
4/29/08