Crown CT26008HX Manual Original página 16

ing process of the battery 6 is terminated due to
inappropriate temperature� When the temperature
conditions are normal, the process of charging will
resume�
• Fig� 4�5, 6�5 - (the red indicator 10 is blinking, the
battery 6 is inserted in the charger 7) - the charging
process of the battery 6 is terminated because of its
failure� Replace the faulty battery 6, its further use is
prohibited�
In the process of charging the battery 6
and the charger 7 become hot, it is a nor-
mal process.
Switching the power tool on / off
Switching on:
Push and release on / off switch 2�
Switching off:
Push and release on / off switch 2�
Design features of the power tool
Temperature protection
Temperature protection automatically switches off the
power tool if the temperature of battery 6 exceeds 70°C�
This protects the power tool from damage if the operat-
ing conditions are not complied with�
Overdischarge protection
The battery 6 is protected by the safety system against
deep discharge� In case of complete discharge, the
power tool is automatically switched off� Attention: do
not try to switch on the power tool when the protec-
tion system is activated the battery 6 can be dam-
aged.
Indicators of the state of battery charge (see
fig. 4.6, 6.6)
With the push of the button 12 the indicators 13 show
the state of charge of the battery 6 (see fig. 4�6, 6�6)�
Swivel head (see fig. 7.1)
Swivel head 1 can be rotated relative to body 3 (angle
of rotation is 180°), as shown in figure 7.1.
Body rotation (see fig. 7.2-7.3)
Body 3 can be rotated (angle of rotation 90°), as shown
in figure 7.3.
• Press and hold lock button 4 (see fig. 7.2).
• Turn body 3 (see fig. 7.3).
• Release lock button 4 (see fig. 7.2).
Recommendations on the power tool op-
eration
• Ensure that the use of the power tool will not cause
violation of the safety regulations (see above)�
• The minimum distance between the power tool
and the illuminated surfaces must be at least 0,2m
(see fig� 8)� Otherwise there is a danger of heating
the illuminated objects, which can cause a
fire�
• Turning swivel head 1 and body 3, you can choose
the position which is the most convenient for work�
• Turn on the power tool� You can either hold the
power tool in your hand, or hang it by belt clip 5
(for example, on the belt), or install it on horizontal
surfaces�
• After use, turn off the power tool, wait a while for it
to cool, and then put it in storage� It is recommended
to store the power tool with the battery dis-
connected�
Power tool maintenance / preventive
measures
Battery maintenance instruction
• Charge timely before the battery 6 is completely
exhausted� Stop operation in low power and charge
it immediately�
• Do not overcharge when the battery 6 is full, other-
wise it will shorten the life time�
• Charge battery 6 in the room temperature of 10°C
to 40°C (50°F to 104°F)�
• Charge battery 6 every 6 months without operation
for a long time�
• Replace worn out batteries in time� Decline of
production or a significantly shorter runtime of the
power tool after charging indicates aging of the
battery 6 and the need for replacement� It should be
taken into account that the battery 6 may discharge
faster if the works take place in the temperature
below 0°С.
• In case of long time storage without use, it is recom-
mended to store the battery 6 at room temperature, it
should be charged to 50%�
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean�
After-sales service and application service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts� Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.crown-tools.com�
Transportation of the power tools
• Categorically not to drop any mechanical impact on
the packaging during transport�
• When unloading / loading is not allowed to use any
kind of technology that works on the principle of clamp-
ing packaging�
Li-Ion batteries
The contained Li-Ion batteries are subject to the Dan-
gerous Goods Legislation requirements� The user can
English
16