Publicidad
Idiomas disponibles
Idiomas disponibles
the 19" / 10" rack cabinet, or properly unscrewed in case of disassembly. It is unacceptable, if any elements of the strips or constituting
its integrity are not properly fixed / applied or pose a threat by their incorrect isolation from other functioning elements, that would
cause hazard in contact.
• In the case of external devices connected to the strip (PDU), the manufacturer's user manual must be strictly followed.
• In order to ensure the highest safety precautions and compliance, please only use components, that are recommended by the server
chassis manufacturer, or fully comply with this particular device specifications.
• Never lead to a situation, in which the strip will be covered from any side. It is necessary to keep the minimum spacing between
devices installed within the 19" / 10" rack cabinet and the strip (PDU) (approx. 10 mm) to allow the minimum heat flow generated by
the operation of the strip (PDU).
• It is strictly forbidden to use strips in a series (even if they are only two of them, one connected to the other with a small load).
• On the sockets found on the PDU strip, as well as its cables, it is forbidden to use switches, adapters (e.g. for another socket), extension
cables or other devices that would in any way mediate the power distribution, but they were not an original part of the strip itself, with
the exception of attached devices, for direct power supply.
• Connect only these devices to the power distribution units (PDU) that are compatible and compliant with the specification given by
the manufacturer of the specific, connected device, as well as, the PDU itself.
• Do not use the power distribution unit (PDU) to operate beyond the rated load values. It is forbidden to connect individual or multiple
devices that will exceed the individual current values specified within the specification, provided by the PDU manufacturer, or may
result in the strip being overloaded.
1.4 Transport
During transport, store the power distribution units (PDU) only in the original packaging in order to protect against shocks and impacts.
Do not dispose of the packaging into garbage disposal. In the case of warranty shipment of the PDU, it must be categorically packed in
the original packaging, it came with.
1.5 Warranty
The warranty does not apply if there are faults and defects, resulting from misuse of the PDU and improper handling of the unit (non-
complying with this manual). Mechanical damage is the basis for rejecting a complaint.
1.6 Proper unpacking, inspection, storage and ventilation
Carefully unpack the device from the transport carton. Check if the following items are in the package:
•
Power distribution unit (PDU) 19" / 10",
•
User's manual,
•
Accessories for fixing the PDU to a 19" / 10" rack cabinet (4 M6 screws, 4 washers, 4 metal baskets).
In the event of any above mentioned elements being missing or damaged, a discrepancy / shortage report should be listed, as long
as it is possible, and it is obligatory to inform the seller and the carrier, immediately, regarding this situation, on the same day, as the
delivery date. This product should only be installed in a specific location with restricted access (separate rooms for ICT equipment etc.).
In addition to that, do not install or store this device in places, where excessive humidity, electrical noise or electromagnetic fields, occur.
Condensation may occur if the device is moved directly from cold to warm environment. In that case, make sure that PDU is completely
dry, before using it.
2. Assembly within ICT rack / 19" / 10" rack cabinets
1. Select 1 unused 1U slot on the vertical mounting rails of the ICT rack / 19" / 10" rack and align those holes with the holes found on the
power distribution unit (PDU).
2. Insert up to 4 metal baskets, bent at the end, with mounting basis inside them, into up to 4 designated holes (mentioned in point
(1)), in such way, so the bent ends of metal baskets will slide, click into and grab the designated holes on the vertical mounting rails,
from the outside.
3. Enter up to 4 screw washers and then insert and screw up to 4 M6 screws from the outside through the selected holes (point (1)) of
the vertical mounting rails.
3. Connecting and disconnecting the PDU and connecting and disconnecting the devices to or from the PDU
1. To connect the power strips to the mains or the UPS, insert the plug of the input cable of the switched off power strip into the
appropriate socket of the power source, which will correspond fully to the specification of the PDU's plug. Then turn on the strip by
switching the switch to the "ON" position – only PDU for 19" racks. In the case of PDU 03 series (intended only for assembling in 10"
cabinets) connecting the plug of PDU to the source power socket will cause the current will appear on PDU output sockets.
2. To disconnect the power strip, turn it off first, and then remove the plug of the input cable from the source power outlet – only PDU
for 19" racks. In the case of PDU 03 series (intended only for assembling in 10" cabinets) turn off the connected devices and pull out
their plugs from the outlet sockets of PDU, and then pull out the PDU plug from the source power socket.
3. To connect an external device to the terminal, insert the plug of this device in its appropriate socket, which will correspond fully to
the specification of the plug of the output socket of the strip.
4. To disconnect the external device from the PDU, remove the plug from its socket by switching off, beforehand, the external device (if
it is possible).
Lanberg © 2015-2021
Publicidad
