Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
_
Mount the table top to the mounting point using
the bolts (28).
- First fit the bolts in the mounting holes on the left-
hand side of the protractor (fig. F).
- Place the table top at an angle so that the
mounting holes on the right-hand side of the
protractor become visible.
- Subsequently fit the bolts in the mounting holes on
the right-hand side of the protractor (fig. G).
_
Firmly tighten the bolts.
Mounting the scale (fig. H)
_
Fit the pin (29) into the slot.
_
Loosen the screws (30).
_
Align the slots (31) with the screws. Align the
mounting hole (32) with the pin. Slide the screws
into the slots, making sure the pin engages with the
mounting hole.
_
Tighten the screws.
Adjusting the sawing angle (fig. A & I)
The default angle between the saw band and the
saw table is 90°.
_
Remove the saw band protection (5 & 6).
_
Loosen the screw (33) and use a set square to
check that the angle between the saw band (4) and
the table top (3) is 90°.
If the angle is not exactly 90°, adjust as follows:
_
Turn the screw to adjust the sawing angle.
Adjusting the saw band (fig. A & J)
The saw band has been adjusted correctly when it
is centered on
the saw band wheels and does not show wobble.
_
Loosen the screws (13 & 14) and open the covers
(7 & 8).
_
Turn the saw band (4) around by turning the upper
saw band wheel (34) into the sawing direction, and
check the running of the saw band.
_
Remove the saw band protection (5).
If adjustment is required, proceed as follows:
_
Slacken the height adjuster (10) and slide the saw
band until it is centered on the wheel.
_
Check the running of the saw band again and
further adjust if required.
_
Tighten the height adjuster.
Adjusting the saw band guides (fig. A, K & L)
The saw band guides have been adjusted correctly
if the saw band has a clearance of max. 1 mm.
Upper saw band guide
_
Remove the saw band protection (5).
_
Move the saw band guide to its upper position
using the height adjuster (11).
_
Loosen the screws (35).
_
Adjust the saw band guide (36) so that the saw
band (4) runs along the longitudinal guides (39 &
40) on both sides.
_
Tighten the screws.
_
Adjust the guide roller (38) using the adjusting
screw (37).
_
Set the longitudinal guides to the correct distance.
Adjustment of the longitudinal guides is performed
as follows:
_
The left-hand guide (39) can be manually adjusted
by loosening the screw (41).
_
The right-hand guide (40) can be manually
adjusted by loosening the screw (42).
Lower saw band guide
_
Remove the saw band protection (6).
_
Slacken the screw (43).
_
Set the guide (44) to the required distance.
_
Tighten the locking knob.
_
Set the longitudinal guides (45 & 46) to the correct
distance.
Adjustment of the longitudinal guides is performed
as follows:
_
The left-hand guide (45) can be manually adjusted
by loosening the screw (47).
_
The right-hand guide (46) can be manually
adjusted by loosening the screw (48).
Replacing the saw band (fig. A, M & N)
_
Loosen the screws (13 & 14) and open the covers
(7 & 8).
_
Put the upper saw band wheel (34) into its lowest
position by loosening the height adjuster (10) and
the adjusting screw (9).
_
Slacken the screws (49) a few threads and
remove the wheelbrush (50) from the lower saw
band wheel (51).
_
Remove the old band.
_
Put the new band (4) round the saw band wheels
as shown.
First put the blade round the upper wheel, then,
while holding the blade in place, put it round the
lower wheel.
_
Adjust the band.
_
Adjust the guides.
_
Tension the band by tightening the adjusting
screw (9).
_
Fit the wheelbrush using the screw.
_
Close the covers and tighten the screws.
Before changing a saw band,
always unplug the machine.
Only use sharp and undamaged
Bent saw bands should be replaced
Always mount the saw band with
the teeth pointing down.
Set the correct saw band tension to
help avoid breaking the blade.
Setting the bevel angle (fig. O)
The bevel angle is infinitely variable between 0° and
45°.
_
Slacken the screw (19).
_
Set the required bevel angle. The setting can be
read from the scale (52).
_
Securely tighten the screw.
Mounting and adjusting the mitre gauge (fig. P)
The mitre gauge can be mounted both to the left
and to the right of the saw band.
_
Loosen the screws (53).
_
Slide the guide profile (54) with the slot (55) over
the bolts (56).
_
Tighten the screws.
_
Slide the mitre gauge (57) into the slot (58) to the
left or right of the saw band (4) as required.
saw bands.
immediately.
17
Publicidad
Tabla de contenido
