Intended Use; General Safety Warnings - Samoa 160 500 Manual Del Usuario

EN

INTENDED USE

The battery-operated grease gun is intended exclusively for pumping grease (NLGI 1 / NLGI 2) for general lubrication applications. Do not exceed the
operating ranges of the technical specifications.

GENERAL SAFETY WARNINGS

WARNING: Read all safety warnings, specifications and
!
instructions provided with this power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark areas
may cause accidents.
• Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
ELECTRICAL SAFETY
• Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, stoves and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating the power tool may result in serious
personal injury.
• Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, safety gloves, non-skid
safety shoes, hard helmet or hearing protection used for appropriate
conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch
or energising power tools that have the switch on invites accidents.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
• Remove the battery pack from the power tool before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
• Store power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
2
816 809 R. 10/20
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
• Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control of the power tool.
• If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
• Avoid forced postures. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
• Wear suitable work clothing. Do not wear loose clothing or jewellery.
Keep your hair and clothing away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
• Do not let confidence gained from frequent use of tools allow you to
ignore tool safety principles. A careless action can cause severe injury
within a fraction of a second.
• Maintain power tools and accessories in good working conditions.
Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Use the power tool and accessories in accordance with these
instructions, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and
grease. Slippery handles and grasping surfaces do not allow for safe
handling and control of the tool in unexpected situations.