monzana DBDL006 Manual Del Usuario página 12

Retainer
No-Mar-Tip
Maintenance
Always turn off the appliance before performing
any maintenance or checks.
Check all parts for signs of wear. If any problems
are detected, do not use the product. Always
replace all parts with original replacements
according to the manufacturer's guidelines.
If the product is not properly cared for and
maintained, it can become unsafe and can also
become damaged. This can lead to dangerous
situations.
Regular maintenance on the product helps to
make the product safe and will also increase its
lifespan.
Removing blockages
Remove a jammed nail using the following
procedure:
1. Disconnect the hose.
2. Remove the nails from the magazine otherwise
all the nails will be ejected from the front.
3. Remove all the small screws (A) and take the
front plate off (B).
4. Carefully remove the jammed nail with pliers
or a screwdriver, without bending or damaging
the driver plate.
5. Replace the front plate (B) on the front (C) and
tighten the screws (A).
6. Connect the compressed air hose to the device
again.
7. Load the nails
Front
plate (B)
Screw (A)
Front (C)
Cleaning
• When cleaning, please make sure that no
parts of the device are disassembled because
components could be lost inside or parts that
contribute to the safety of the appliance could
be reassembled incorrectly.
• Vents, the contact element and the trigger
must be kept clean and free of debris. Clean the
device regularly with compressed air.
• Clean the magazine, removing any metal and
wood chips that may have accumulated in the
magazine. Clean the magazine regularly with
compressed air.
• Do not use cleaners such as gasoline, carbon
tetrachloride, ammonia as these can damage
plastic parts and the o-rings.
Storage
• Store the device in a safe place and out of reach
of children and unauthorised people.
• When not in use, the device should be
disconnected from the compressed air supply
and stored in a warm, dry place in its carrying
case. If the device is stored for a long period of
time, treat the metal surfaces with a thin layer
of oil to prevent rust. Store the unit in a cool
environment.
www.Deuba24online.de
Advice on connecting the air supply
For better performance, install a 3/8 inch quick
connector (¼ inch NPT threads) with an inner
diameter of 8mm (0.315 inch) to the nailer and a
3/8 inch quick connector to the air hose.
1. Switch the ON/OFF switch on the compressor
to the OFF position. Plug the compressor into
the socket.
2. Connect the pressure regulator by turning it
fully anti-clockwise. Turn on the compressor
and let it run until it automatically shuts down.
3. Connect the air hose to the pressure regulator.
Turn the valve on the pressure regulator to the
right to a pressure of between 70 PSI and 110
PSI.
Troubleshooting
PROBLEM
There is a leak at the top of
the device or in the trigger
area.
There is a leak underneath
the device.
The device is not working or
only works with difficulty.
Nails are jamming
frequently.
22 23 www.Deuba 24onl i ne.d e
4. Load the nails into the nail gun.
5. When doing this, make sure you point the nail
gun in a safe direction.
6. The nail unit is ready. You may need to change
the pressure for the right drive depth.
POTENTIAL CAUSE SOLUTION
1. Loose screws. 1. Schrauben anziehen
2. Broken or damaged 2. Überholsatz installieren
O-Rings or seals.
1. Loose screws. 1. Schrauben anziehen
2. Broken or damaged 2. Überholsatz installieren
O-Rings or seals.
1. Insufficient air pressure. 1. Set the compressor to between 70
2. Insufficient lubrication. PSI and 110 PSI.
3. The vents are blocked. 2. Apply 2–3 drops of oil to the
4. The O-Rings or seals are compressed air connection.
worn 3. Clean the vents.
4. Fit replacement parts.
1. The driver is worn. 1. Repair the driver.
2. he piston is damaged or 2. Replace the piston.
worn. 3. Remove bent nails and replace with
3. Nails are bent. straight nails.
4. There is dirt in the 4. Clean the magazine.
magazine. 5. Tighten the screws.
5. The magazine is loose. 6. Replace with the correct nails.
6. Incorrect nails are used.