monzana DBDL006 Manual Del Usuario página 9

• Handle the device with care. Keeping it clean
and oiling it will lead to safer and better
operation.
• Never hold or carry the device by the hose!
• Always store the device out of the reach of
children and other people who are not fa-miliar
with handling the device. Tools in the hands of
unauthorised people can be dan-gerous.
• Place the device correctly on the work surface.
Do not fire staples directly onto other staples or
at an angle that is too severe. The staples can
rebound and cause injuries.
• Do not use the device as a hammer!
• Store screws and coverings neatly!
• Keep your face, hands, feet and other body parts
at a safe distance from the drive mechanism.
• Only disconnect the device from the air hose
when your finger is not on the trigger. The
device may fire when it is reconnected.
• Do not load the device with your finger on the
trigger or when the retainer is activated.
• Do not fire staples into thin boards, near the
edges or on corners of a workpiece. Staples can
break and cause injury.
• Always disconnect the air hose for:
• Maintenance, inspections and repairs;
• Twisting the exhaust duct;
• Changing the no-mar tip;
• Removing blockages;
• Non-use;
• Transport;
• Handing over to another person.
• Only use parts that are specified by the
manufacturer for this specific model. Using
unauthorised parts and not following the
maintenance instructions can lead to increased
risk of injury.
• Only use oil and grease that are specifically
intended for the device.
• Servicing and repairs on the device should only
be carried out by an authorised person.
• Never use oxygen, other cylinder gases or
combustible gases as propellants. These are
dangerous and can cause explosions.
• Never exceed the maximum pressure listed
on the device. Use only clean, dry, regulated,
compressed air within the range listed on
the device. Never connect the device with a
pressure source that exceeds 200 PSI.
• Be careful with the hose. Avoid knots,
constrictions and contact with solvents or
objects. Replace damaged hoses immediately
as they could break and swirl around.
• Check the connections, hoses and the
compressor before each use. Repair or replace
damaged hoses and connections immediately.
The hose can easily burst, causing personal
injury.
Adjustable air
Hand grip Compressed
outlet
air connection
Trigger
Air cap
Magazine
lock
Casing
Magazine
Retainer
Nail indicator
No-Mar-Tip
www.Deuba24online.de
Nail / Staple types:
2mm(0.079")
10mm 3/8"
15mm 5/8"
20mm 3/4"
25mm 1"
30mm 1-3/16"
32mm 1-1/4"
35mm 1-3/8"
38mm 1-1/2"
40mm 1-5/8"
45mm 1-3/4"
50mm 2"
1.26 x 1.05mm
(0.050")(0.041")
18Ga.
TECHNICAL DATA
PRODUCT SIZE:
Length
Width
Height
WEIGHT
NORMAL OPERATING
PRESSURE
MAGAZINE CAPACITY
TRIGGER MECHANISM
NAIL SIZE
18-Gauge nails
18-Gauge staples
Features
• 360° adjustable exhaust duct.
• Allows the user to divert dirty air.
• Comfortable grip.
• For better comfort and control.
• Ergonomic casing.
• Durable and comfortable for long periods of use
16 17 www.Deuba 24onl i ne.d e
Follow the steps below to prepare your device
for use:
5/7mm(1/4")
1. All users and their immediate supervisor must
be familiar with the safety instructions for
operators prior to use.
2. Each device has its own copy of the safety
instructions. Keep these documents handy for
13mm 1/2"
16mm 5/8"
future reference.
19mm 3/4"
3. Install a filter, a pressure regulator, a lubrication
25mm 1"
system and a water separator into your
32mm 1-1/4"
compressed air unit as per the manufacturer's
38mm 1-1/2"
instructions. Also, install a pressure gauge as
40mm 1-5/8"
close as possible to the staple unit, preferably
1.26 x 1.05mm
within 3m.
(0.050")(0.041")
4. Select pressure hoses with an internal
18Ga.
diameter of at least 0.64cm and a maximum
length of 30m.
CAUTION: To reduce the risk of injury caused
by a burst hose, use a hose which is designed
225mm
for a minimum of 200 PSI.
240mm
5. Use the correct connectors for the hose.
56mm
The stapler and air hose need a coupling so
no pressure remains when the connector is
1,30kg
separated.
CAUTION: Never use non pressure-relieving
70-110 PS (0,5-
and/or quick coupling sockets on this device.
0,75MPa)
Non pressure-relieving couplings and female
100 Nail
couplings store pressure in the device after
Contact release
separation of the compressed air connection.
10-50mm
This leaves sufficient pressure in the device
13-40mm
to fire a staple even after separation of the
compressed air
pneumatic connectors can be used with the
nail gun so that the compressed air escapes
from the device as soon as the compressed air
connection is disconnected.
6. Set the pressure regulator to between 70 PSI
and 110 PSI. The best pressure is the lowest
level at which you can successfully work.
connection. Only male