Cleaning And Maintenance; Care And Maintenance - Chicco Rainbow Instrucciones De Uso

Ocultar thumbs

página de 40

/ 40
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

CHICCO RAINBOW BABY WALKER

Parts

A) Baby walking frame

B) Padded seat with semi-rigid backrest

C) 2 front swivel wheels

D) 2 rear fixed wheels

E) 6 stoppers

F) Play panel (NOTE: the toy contained in the box may

differ from the one illustrated in diagram F)

G) Fastening key for toy panel

HOW TO ASSEMBLE THE BABY WALKING FRAME

1. Turn the baby-walking frame (A) upside down. Fit the

wheels (C) in the appropriate housings using the plastic

tool, as shown in diagram 1. Ensure that the wheels'

male securing pin is safely locked into position in each

housing.

2. Fit the rear wheels (D) into the designated seats, as

seen in diagram 2. Ensure that the wheels' male secur-

ing pin is safely locked into position in each housing:

you will hear it click into place and the rod connector

pin will now be visible.

3. Fit the stoppers (E) into the appropriate housings, as

shown in diagram 3A. Ensure that the joints of all the

stoppers are firmly and correctly fitted to the end (dia-

gram 3B).

4. Position the baby walker ready for use with the wheels

on the floor (on a flat surface);lift the tray slightly as

seen in diagram 4, pulling it upwards until you hear it

click into position at the desired height.

WARNING: Before placing the child in the baby-walk-

ing frame, ensure that the blue button, located under

the small table, is safely locked: a click will be heard,

indicating that the button is locked into position.

See diagram 5.

5. Insert the plastic rings of the padded seat (B) in the

slots located along the upper edge of the baby-walking

frame (diagram 6A), and ensure that they are correctly

locked in the position, as shown in the diagram 6B.

ADJUSTING THE BABY WALKER

WARNING: when opening, adjusting or closing the product,

ensure that your child is at a safe distance.

6. To open the baby walker, lift the tray slowly pulling it up

towards you until you hear it click into position (diagram

4-5).

7. To adjust the seat height, remove your child from the

walker, push the tray upwards until you hear it click

into position. To lower the height, take hold of the pin

housed under the tray and turn it counter clockwise,

push the pin upwards and allow it to slide as you lower

the tray to the desired position. When the pin is re-

leased, the tray will automatically lock into position

(diagram 7-8).

WARNING: Before placing your child in the baby walk-

er, check that the pin is correctly locked in position, as

seen in diagram 5.

8. To close the baby walker, turn the pin housed under the

tray counter clockwise and push it pin upwards (dia-

gram 7). Lower the seat until it is completed closed.

WARNING: Never close the baby walker with the child

in inside.

PLAY PANEL

The play panel has a variety of activities to develop a ba-

by's sensorial, tactile and hearing skills.

9. To fasten the toy to the frame, place it on the table

indicated in fig. 9. To fix it push both keys upward and

turn them as far as possible (fig. 10). To remove the toy,

repeat the previous instructions in reverse order (fig.

11-12).

• WARNING: This toy must only be used under adult su-

pervision.

• WARNING: Before using the product, remove and di-

spose of any plastic bags and any other packaging (e.g.

fasteners and fixing ties etc) and keep them out of reach

of children.

• WARNING: Before first use, check that the product and

all its components show no signs of damage caused by

transportation. Check the product regularly for signs

of wear and damage. Keep all damaged parts out of

children's reach.

• WARNING: The child may be hurt if you do not follow

these instructions.