Sleep Timer; Motion Sensor; Charging Your Ipod - Logitech Pure-Fi Anytime Manual Del Usuario

Sleep Timer

Logitech Pure-Fi Anytime includes a sleep timer that will automatically turn Logitech Pure-Fi Anytime
™
a set period of time. To activate the sleep timer, press Snooze. To increment the timer, press Snooze repeatedly
– until the desired time is reached. For finer adjustment of the duration, use the |7 8|buttons.
You can turn off the sleep timer in one of two ways:
• Press power ( ). This will also turn Logitech Pure-Fi Anytime
• Repeatedly press Snooze until the display reads 'Off'. This will leave Logitech Pure-Fi Anytime
Note
• The sleep timer can only be used if no alarm is currently sounding and no snooze time is active.

Motion Sensor

Your Logitech Pure-Fi Anytime includes an integrated motion sensor. It provides two benefits:
™
Motion-activated backlights
The button backlights automatically turn on when motion is detected above the speaker, allowing you to adjust
the speaker without having to turn on the lights in the room. The backlights will dim a few seconds after motion
is no longer detected.
Motion-sensing snooze
Logitech Pure-Fi Anytime allows you to simply wave your hand above the speaker to activate the snooze
™
feature. This prevents you from having to reach for the snooze button and accidentally knocking your iPod out
of the Universal Dock.

Charging Your iPod

Your iPod battery will charge automatically when your iPod is in Logitech Pure-Fi Anytime
connected to A/C power. Your iPod will not charge if the Logitech Pure-Fi Anytime
up power.
Note: If your iPod is left on while the Logitech Pure-Fi Anytime
will run down.
7
English
off after
™
off.
™
on.
™
's Universal Dock, and
™
is operating on battery back
™
is not connected to AC power, the iPod battery
™
Troubleshooting
My iPod is in the Dock and playing, but I can't hear any music.
• Make sure that Logitech Pure-Fi Anytime is on.
™
• Make sure that the iPod input is selected.
• Make sure that the volume level on Logitech Pure-Fi Anytime
down buttons on the speaker to adjust.
• Try turning off the Sound Check feature on your iPod.
• Download the latest version of iTunes (available at apple.com) and upgrade your iPod to the latest iPod
firmware. Test your iPod with headphones or another speaker.
There isn't a Universal Dock adapter for my iPod.
• Try each of the trays included with your Logitech Pure-Fi Anytime
• Use the Universal Dock adapter that was included with your iPod when you purchased it.
• If you have a 1st, 2nd, or 3rd generation iPod, you need to use the Aux input connector on the back of
Logitech Pure-Fi Anytime . (1st / 2nd generation iPods do not have a dock connector. 3rd generation iPods
™
are not supported by the Logitech Pure-Fi Anytime
The FM radio reception is poor.
• Make sure that the FM antenna is fully extended. Leaving the antenna coiled up will result in poor reception.
The remote isn't working.
• Point the remote directly at Logitech Pure-Fi Anytime
• Make sure the remote sensor isn't being blocked.
• Try using a new battery in the remote.
The display and controls are too bright / dim.
Use the Brightness button to adjust the brightness level.
My iPod screen says "OK to disconnect" or "Accessory attached."
Depending on your iPod model, these messages may appear when playing iPod playlist presets. Once the music
has started playing, the iPod screen will return to normal.
For the most up-to-date troubleshooting information, visit www.logitech.com
is at least half way up. Use the volume up and
™
and use the tray that provides the best fit.
™
's Universal Dock.)
™
.
™
8
English